(e)
Install the nuts (5).
(f)
Torque the nuts (5) to between 0.6 and 0.7 m.daN (53.09 and 61.94 lbf.in)
(g)
Put the cover (3) in position and install the screws (4). WARNING : WEAR GOGGLES WHEN YOU REMOVE OR INSTALL THE LOCKWIRE.
_______ CUT, REMOVE AND DISCARD THE LOCKWIRE AS YOU DO THE TASK. LOOSE LOCKWIRE CAN CUT OR BLIND YOU.
(h)
Safety the screws (4) with MISCELLANEOUS (Material No. 19-010).
(5) Seal the Splitline Joints and the Galley/Floor Interface
(a) Make sure that all the old sealant has been removed from the splitline joints and the galley/floor interface.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE_______ WORK AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(b) Apply new BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A) into all the splitline joints and at the galley/floor interface.
R **ON A/C 151-199,
R Subtask 25-31-41-420-050-B
R A. Connect the Galley Splitline
R R NOTE : This procedure is only necessary if you removed the galley from____ the cabin.
R (1) Unless specified TORQUE all nuts, bolts and screws (Ref. TASK 20-21-11-911-001).
R R (2) Install the Floor Fittings (Ref. Fig. 404C/TASK 25-31-41-991-019-B)
R (a) Install the new o-rings (19).
R (b) Install the bushings (18).
CES
R (c) Put the fittings (17) in position.
R (d) Put the shims (16) in position as identified during the removal
R procedure.
R (e) Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-002) on the
R threads of the bolts (15).
R (f) Put the washers (20) in position and install the bolts (15).
R (g) Install the bushing (24).
R (3) Connect the Galley at the Splitline
R (Ref. Fig. 407/TASK 25-31-41-991-002)
R WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME_______
R DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
R NOTE : The splitline screws and bolts are painted red.____
R (a) Prevent damage to the component interface and the adjacent area.
R (b) Carefully put the galley modules (88) and (80) in position.
R (c) Install the washers (86) and the screws (87).
R (d) Install the screws (85).
R (e) Install the washers (84) and the screws (83).
R (f) Put the galley module (81) in position.
R (g) Install the screws (82).
R (4) Seal the Splitline Joints
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE_______
R THIS/THESE MATERIAL/S.
R USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
R (a) Remove the old sealant of the splitline joints with a
R nonmetallic-scraper.
R (b) Clean the splitline joints with CLEANING AGENTS (Material No. 11-
R 003) and a lint-free cloth.
R (c) Apply new BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004A)
R into all the splitline joints.
R (d) Connect the supply connections as necessary.
R (5) Carefully lift the galley above the shims (16).
R (Ref. Fig. 404C/TASK 25-31-41-991-019-B)
R Subtask 25-31-41-420-062-B
R B. Installation of the Galley Unit
R (1) Install the Galley Unit
R (a) Unless specified TORQUE all nuts, bolts and screws (Ref. TASK 20-
21-11-911-001).
R WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME_______
R DAMAGED OR INJURE PERSONNEL. THE UNIT/ASSEMBLY IS
R HEAVY.
R (b) Prevent damage to the component interface and the adjacent area.
R (c) Put the galley unit in position.
R (2) Install the Lower Attachments
R (Ref. Fig. 404C/TASK 25-31-41-991-019-B)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(13)
