_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______
-FLUSH IT AWAY WITH CLEAN WATER
-GET MEDICAL AID. CAUTION : USE ONLY THE SPECIFIED MATERIALS AND OBEY THE INSTRUCTIONS FROM
_______ THE MANUFACTURERS. OTHER MATERIALS CAN CAUSE DAMAGE TO THE SURFACE PROTECTION OF THE COMPONENTS AND THE RELATED AREA.
(1)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(2)
Clean the component interface and/or the adjacent area.
(3)
Make sure that the insulation box is not damaged.
(4)
Apply SPECIAL MATERIALS (Material No. 05-002) to the threads of the screws (4),(16) and (25).
Subtask 25-53-51-420-050
B. Installation of the air-stop drain valve
(1)
Put the top lid (1) in position on the air-stop valve (11).
(2)
Put the air-stop drain valve (11) with the top lid (1) in position.
(3)
Attach the drain pipes to the air-stop drain valve (11) (Ref. TASK 25-53-00-400-001).
(4)
Put the bracket (3) in position on the structure.
(5)
Install the screws (16),(25), the washers (17),(26), the nuts
(18),(27) and tighten.
NOTE : The items (25),(26) and (27) are only installed in the AFT
____
cargo compartment
(6)
Loosely install the screws (4), the washers (5) and the insulation
plates (2). Do not tighten the screws (4) at this time.
(7)
Put the bonding strap (6) in position and install the screw (8) and the washer (7) (Ref. TASK 20-28-00-912-004).
(8)
Connect the thermostat (14) (Ref. TASK 30-71-54-400-001).
(9)
Put the sides (9), (15) in position. At the same time put the wire
(13) through its related hole in the side (15).
(10)
Put the bottom lid (12) in position.
(11)
Put the straps (10) around the insulation box and make sure that the center strap is between the insulation plate (2) and the brackets (3) and (19).
(12)
Tighten the straps (10). NOTE : Make sure that the straps are not too tight and that the
____ insulation box is not compressed. Make sure that there is no gap between the joints.
(13)
Connect the wires (13) of the heating disk (Ref. TASK 30-71-55-000-001) at its terminal.
(14)
Tighten the screws (4).
(15)
Apply the STORAGE PRESERVATION (Material No. 15-006) to the fasteners and all other connection elements.
(16)
Apply the SPECIAL MATERIALS (Material No. 05-005) to the material applied to the fasteners and the connection elements.
5. Close-up
________ Subtask 25-53-51-860-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the floor panels 131TF, 132TF in the FWD cargo compartment (Ref. TASK 53-22-14-400-001).
(3)
Install the floor panels 151AG, 152AG, 151BG, 152BG in the AFT cargo compartment (Ref. TASK 53-42-14-400-001).
Subtask 25-53-51-865-052
B. Remove the safety clip(s) and the tag(s) and close this (these) circuit breaker(s): 1DU, 20DU, 2MY, 3MY and/or 21DU, 32DU, 102MY, 103MY.
Subtask 25-53-51-410-051
C. Close Access
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
(3)
Remove the actuator safety locks and close the FWD and/or AFT cargo-compartment door(s) (Ref. TASK 52-30-00-860-002).
LININGS AND FURNISHINGS/FWD CARGO COMPARTMENT - DESCRIPTION AND OPERATION
_________________________________________________________________________
1. General
_______
**ON A/C 001-003,
The FWD cargo hold is in Zone 130 between the fixed partitions FR24A and FR34. The FWD cargo hold is specified as the FWD cargo compartment. The FWD cargo compartment door which is found between FR24A and FR28 gives access to the FWD cargo compartment . Included in the FWD cargo compartment are the subsequent linings:
-
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(165)
