(b)
 Put a container below the water connections you will disconnect.

 (c)
 Disconnect the connections (63) and (64) and remove the potable water tube (62).

 (d)
 Disconnect the connection (69).

 EFF : ALL
25-43-41Page 408
Config-2 May 01/04
R
 CES

 Pelment and Door Assembly - Component Location Figure 401/TASK 25-43-41-991-020
R  EFF : CES  ALL  Page 40925-43-41 Config-2 May 01/04 

 Lavatory Door Attachments Figure 402/TASK 25-43-41-991-021
R  EFF : CES  ALL  Page 41025-43-41 Config-2 Feb 01/03 

 Water Tube Connection Figure 403/TASK 25-43-41-991-015
R  EFF : CES  ALL  Page 41125-43-41 Config-2 Feb 01/03 

 (e)
 Remove the nut (67), the washer (66) and disconnect the bonding straps (65) and (68).

 (f)
 Loosen the clamp (71) and disconnect the sleeve (72) from the drain tube (70).

 (g)
 Put blanking plugs on the disconnected line ends.

 (h) Remove the container. Subtask 25-43-41-020-060
 B. Disassembly of the Lavatory D
 (1)
 Remove the upper and lower attachments.
 (Ref. Fig. 404/TASK 25-43-41-991-022)

 (a)
 Remove the wall fitting cover (84).

 (b)
 Remove the bolts (82).

 (c)
 Above the lavatory ceiling, remove the quick release pin (85).

 (d)
 Lift and move the lavatory assembly to the centre of the aircraft aisle.

 (e)
 Remove and discard the packings (83).

 (2)
 Disconnect the air supply.
 (Ref. Fig. 405/TASK 25-43-41-991-002)

 (a)
 Above the lavatory ceiling, loosen the clamp (42) and disconnect the air extraction hose (41).

 (b)
 Behind the lavatory, loosen the clamp (45) and disconnect the ventilation hose (46).

 (c)
 Loosen the clamp (48) and disconnect the ventilation hose (47).

 (d)
 Remove the screw (51), the washer (50), the spacer (49) and the clamp (52).

 (3)
 Disconnect the electrical connections.
 (Ref. Fig. 406/TASK 25-43-41-991-023)

 (a) Disconnect the electrical connector (106).
 EFF : ALL
25-43-41Page 412
Config-2 May 01/04
R
 CES

 Upper and Lower Lavatory Attachments Figure 404/TASK 25-43-41-991-022
R  EFF : CES  ALL  Page 41325-43-41 Config-2 May 01/04 

 Hose Connection Figure 405/TASK 25-43-41-991-002
R  EFF : CES  ALL  Page 41425-43-41 Config-2 Feb 01/03 

 Electrical Connections Figure 406/TASK 25-43-41-991-023 
R  EFF :  ALL  Page 41525-43-41 Config-2 May 01/01
 CES 

 (b)
 Put blanking caps on the disconnected electrical connectors.

 (c)
 Remove and discard the cable ties (112) from the mounts (111).

 (d)
 Remove and discard the cable ties (114) from the bonding strap

 (113) and the cable assembly (105) where necessary.

 (e)
 Remove the screws (103), the washers (104) and remove the bracket (107).

 (f)
 Disconnect the electrical connectors from the flush switch (102).

 (g)
 Put blanking caps on the disconnected electrical connectors.

 (h)
 Remove and discard the cable ties (109) from the mounts (108).

 (i)
 Temporarily attach the cable assembly (110) to the top of the ceiling panel (101).

 (j)
 Close the sanitary cabinet door (61).

 (4) Remove the subassemblies. (Ref. Fig. 407/TASK 25-43-41-991-024)
 (a)
 Remove the sealant from around the floor pan (121).

 (b)
 Remove the screws (124).

 (c)
 Remove the screws (122) and the washers (123).

 (d)
 Lift and remove the lavatory assembly from the floor pan (121).

 (e)
 Remove the screws (126), the screws (124) and the washers (125) from the ceiling panel (101).

 (f)
 Temporarily attach the ventilation hose (47) to the top of the ceiling panel (101).

 (g)
 Remove the screw (127).

 (h)
 Remove the screws (130) and the washers (129).

 (i)
 Move the subassemblies (128) and (131) apart.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備3(86)