Subtask 27-92-13-481-050
D. Install Locking Devices
(1) Put the PIN-SIDE STICK LOCKING in the CAPT and F/O side stick
controllers. R
Subtask 27-92-13-941-050
E. Safety Precautions
(1)
Put the warning notices in the flight compartment to tell persons not to operate the flight controls.
(2)
Put the warning notices in position to tell persons not to operate the hydraulic systems.
(3) Put the access platform in position at zones 334 and/or 344.
Subtask 27-92-13-020-050
F. Access
(1) Open the horizontal stabilizer trailing edge access panels (Ref. TASK 55-13-11-000-001). For 49 CE1 remove panels 334BT and 334DB For 49 CE2 remove panels 344BT and 344DB
4. Procedure
_________
(Ref. Fig. 401/TASK 27-92-13-991-001)
Subtask 27-92-13-020-052
A. Disconnect the Bonding Strap and the Electrical Connectors
(1)
Disconnect the bonding strap from the control rod.
(2)
Remove the nut (11), the washer (10), and the bolt (8). Disconnect the bonding strap (9).
(3)
Disconnect the electrical connectors (3) from the receptacles (2).
(4)
Put blanking caps on the disconnected electrical connectors.
Elevator-Servocontrol Position Transducer Unit Figure 401/TASK 27-92-13-991-001
1EFF : 1 1R 1CES ALL 1 11 1 27-92-13 Page 404 Feb 01/00
Subtask 27-92-13-020-051
B. Removal of the Elevator Position Transducer
R R (1) Make sure that the rigging pin can be inserted in the elevator position transducer
R NOTE : The rigging pin is part of the position transducer____
R (2) Remove and discard the cotter pin (14).
R (3) Remove the nut (13), the washer (12), the bolt (5) and the bush (6) which attach the control rod (7) to the elevator position transducer (1).
R (4) Remove the control rod (7) from the elevator position transducer (1).
R (5) Remove the bolts (24) and the washers (25) which attach the mounting bracket (15) to its supports.
R (6) Remove and discard the cotter pins (18) and (22).
R (7) Remove the nuts (17), the washers (16) and the lower attaching bolts (4).
R (8) Remove the nut (21), the washer (20) and the upper attaching bolt (19).
R (9) Remove the elevator position transducer (1) from the mounting bracket (15).
TASK 27-92-13-400-001 Installation of the Elevator Servocontrol Position Transducer Unit 49CE1, 49CE2 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
FALL CAN INJURE OR KILL YOU.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R 98D27903500000 2 PIN-SIDE STICK LOCKING B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 16-003 F ASNB70720
COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱9(16)
