(2)
 Clean the component interface and/or the adjacent area with MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004).

 (3)
 Do an inspection of the component interface and/or the adjacent area.

 (4)
 Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-049) to the bolts (5) and the transducer (3) interface.

 Subtask 27-92-19-420-050
 B. Installation of the Pressure Transducer
 WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.

_______
 (1)
 Lubricate a new O-ring (7) with HYDRAULIC FLUIDS (Material No. 02-003).

 (2)
 Install the new O-ring (7) on the transducer (3).

 (3)
 Put the transducer (3) in position on the manifold (6).

 (4)
 Install the bolts (5), the washers (2) and the nuts (1).

 (5)
 Tighten the nuts (1).

 (6) Connect the electrical connector (4) to the transducer (3). Subtask 27-92-19-614-051
 C. Pressurize the Accumulator
 (1) Pressurize the applicable accumulator with nitrogen (Ref. TASK 12-14-29-614-002).
 Subtask 27-92-19-790-050
 D. Leak Test
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL

_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1)
 Apply SPECIAL MATERIALS (Material No. 05-004A) to the transducer (3) and the manifold (6) joint.

 (2)
 Examine the joint and the adjacent area for leaks. Leaks are not permitted.

 (3)
 If necessary, remove the transducer (3) (Ref. TASK 27-92-19-000-001) and do the installation task again (Ref. TASK 27-92-19-400-001).

 (4)
 Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-004) to clean the transducer (3) and the manifold (6) joint.

 5. Close Up
________
 Subtask 27-92-19-410-050
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the applicable access panel:

 -
FOR 14CE1
 install 575EB (Ref. TASK 57-51-37-400-004)

 -
FOR 14CE2
 install 675EB (Ref. TASK 57-51-37-400-004)

 -
FOR 14CE3
 install 575GB (Ref. TASK 57-51-37-400-004)

 -
FOR 14CE4
 install 675GB (Ref. TASK 57-51-37-400-004).

 Subtask 27-92-19-865-052
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV, 20CE2.
 Subtask 27-92-19-866-052
 C. Move the Spoilers and the Flaps
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1)
 Lower the applicable spoiler (Ref. TASK 27-60-00-866-002):

 -
for the transducer 14CE1 (14CE2) retract the spoiler 4

 -
for the transducer 14CE3 (14CE4) retract the spoiler 5.

 (2)
 Make sure that the maintenance device is in the 'O' (Operation) position.

 (3) Retract the flaps fully (Ref. TASK 27-50-00-866-009). Subtask 27-92-19-863-051
 D. Pressurize the Hydraulic Systems
 WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.

_______
 (1) Pressurize the Green hydraulic system (Ref. TASK 29-10-00-863-001).
 (2) Pressurize the Yellow hydraulic system (Ref. TASK 29-10-00-863-002). Subtask 27-92-19-942-051
 E. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the safety barriers.

 (3)
 Remove the warning notice(s).

 (4)
 Remove the access platform(s).

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 FTU (FORCE TRANSDUCER UNIT) - RUDDER PEDAL (74CE) - REMOVAL/INSTALLATION
________________________________________________________________________
 TASK 27-92-27-000-001
 Removal of the Rudder Pedal Force Transducer (74CE)
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱9(38)