(2)
Tighten the two screws.
(3)
Close the access door 822.
(4)
Remove the access platform(s).
R 1EFF : ALL 1 27-92-41Page 469 1 1 May 01/04 1 1 1CES 1
TASK 27-92-41-000-012 Removal of the Side Stick Spring Rods WARNING : MAKE SURE THAT THE SIDE STICK ASSEMBLY STAYS IN THE VERTICAL POSITION
_______ DURING THE MAINTENANCE PROCEDURES. IF NOT THERE IS A RISK OF SKYDROL LEAKAGE. SKYDROL CAN CAUSE INJURY AND/OR DAMAGE.
1.
Reason for the Job
__________________
This procedure is applicable only for spring rods P/N D27310130000.
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
98DNSA20206080 2 RIGGING PIN 98D27303001001 1 HOLDER - SIDE STICK
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-92-41-000-001 Removal of the Side Stick Assembly 19VU (18VU) 27-92-41-991-014 Fig. 413
3. Job Set-up
__________ Subtask 27-92-41-010-063
A. Remove the side stick assembly (Ref. TASK 27-92-41-000-001). Subtask 27-92-41-480-056
B. Installation of the Tools
(Ref. Fig. 413/TASK 27-92-41-991-014)
(1) Install the side stick assembly on the HOLDER - SIDE STICK (98D27303001001).
1EFF : ALL 1 27-92-41Page 470 1 1 May 01/04R 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1
27-92-41Page 471
1 1 May 01/04 1 1 1CES 1
Spring Rods Figure 413/TASK 27-92-41-991-014- 12 (SHEET 1)
1EFF : 1 1R 1CES ALL 1 11 1 27-92-41 Page 472 May 01/04
Spring Rods Figure 413/TASK 27-92-41-991-014- 22 (SHEET 2)
1EFF : 1 1R 1CES ALL 1 11 1 27-92-41 Page 473 May 01/04
(2) Install the RIGGING PIN (98DNSA20206080) (7) on the roll transducer unit (8) and on the pitch transducer unit (6).
Subtask 27-92-41-010-064
C. Disconnection of the Side Stick Pitch Damper (Upper Attachment Only) (Ref. Fig. 413/TASK 27-92-41-991-014)
(1)
Cut and discard the cotter pin (1) from the nut (2).
(2)
Remove the nut (2) and the washer (3).
(3)
Remove the bolt (4) and disconnect the damper (9) from the bellcrank (11).
4. Procedure
_________ Subtask 27-92-41-020-061
A. Removal of the Side Stick Spring Rods
(1)
Remove and discard the cotter pins (18) from the nuts (15).
(2)
Remove the nuts (15) and the washers (16).
(3)
Remove the bolts (17) and the spring rods (19).
1EFF : ALL 1 27-92-41Page 474 1 1 May 01/04R 1 1 1CES 1
TASK 27-92-41-400-012
Installation of the Side Stick Spring Rods
WARNING : MAKE SURE THAT THE SIDE STICK ASSEMBLY STAYS IN THE VERTICAL POSITION
_______ DURING THE MAINTENANCE PROCEDURES. IF NOT THERE IS A RISK OF SKYDROL LEAKAGE. SKYDROL CAN CAUSE INJURY AND/OR DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific access platform 1.6 m (5 ft. 3 in.) 355M03200001 1 28 VDC POWER SUPPLY TOOL 98DNSA20206080 2 RIGGING PIN 98D27303001001 1 HOLDER - SIDE STICK 98D27303004000 1 TOOL - ARTIFICIAL FEEL RODS 98D27903500000 1 PIN-SIDE STICK LOCKING
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific lockwire-corrosion resistant steel dia. 0.8 mm (0.03 in.)
1EFF : ALL 1 27-92-41Page 475 1 1 May 01/04R 1 1 1CES 1
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM FLIGHT CONTROLS 飛行操縱9(56)
