-------------------------------------------------------------------------------NAME ELECTRICAL LEVEL TO SIGNAL STATUS -------------------------------------------------------------------------------
AP1 AUTHORIZED MON AP2 AUTHORIZED COM AP2 AUTHORIZED MON PITCH AXIS OK COM GND/O C GND/O C GND/O C GND/O C FMGC1 FMGC2 FMGC2 ELAC1 MON SEC1 COM GND=AUTHORIZEDGND=AUTHORIZEDGND=AUTHORIZEDGND=OK
SEC1 MON
SEC2 COM
SEC2 MON
PITCH AXIS OK MON GND/O C ELAC1 COM SEC1 COM GND=OK
SEC1 MON
SEC2 COM
SEC2 MON
- ELAC2
-------------------------------------------------------------------------------NAME ELECTRICAL LEVEL TO SIGNAL STATUS -------------------------------------------------------------------------------
PITCH AXIS OK COM GND/O C ELAC2 MON ELAC1 COM GND=OK
ELAC1 MON
PITCH AXIS OK MON GND/O C ELAC2 COM ELAC1 COM GND=OK
ELAC1 MON
DGTL O/P VALIDATED COM GND/O C ELAC2 MON SEC1 COM GND=VALIDATED
SEC1 MON
FAC1
BSCU
DGTL O/P VALIDATED MON GND/O C ELAC2 COM SEC2 COM GND=VALIDATED
SEC2 MON
SEC3 COM
SEC3 MON
FAC2
BSCU
AP1 AUTHORIZED COM AP1 AUTHORIZED MON AP2 AUTHORIZED COM AP2 AUTHORIZED MON PITCH AXIS OK COM GND/O C GND/O C GND/O C GND/O C GND/O C FMGC1 FMGC1 FMGC2 FMGC2 ELAC2 MON SEC1 COM GND=AUTHORIZEDGND=AUTHORIZEDGND=AUTHORIZEDGND=AUTHORIZEDGND=OK
SEC1 MON
1EFF : ALL 1 27-93-00Page 11 1 1 Feb 01/00R 1 1 1CES 1
-------------------------------------------------------------------------------NAME ELECTRICAL LEVEL TO SIGNAL STATUS -------------------------------------------------------------------------------
SEC2 COM SEC2 MON
PITCH AXIS OK MON GND/O C ELAC2 COM GND=OK SEC1 COM SEC1 MON SEC2 COM SEC2 MON
(3)
Protections All the inputs and outputs are protected against spurious undervoltages by clipper circuits. A 75 ohms resistor ensures the protection against the spurious application of 28VDC or 115VAC. This resistor acts as a fuse at each input and output, except on relay contacts. All the analog and discrete inputs are filtered.
(4)
Power supply of position transducers. Each COM and MON unit supplies the position transducers that it uses: - +10VDC power for side stick transducers (ANI 1)
-7VAC 1953 Hz power for inductive transducers (ANI 2, ANI 3, ANI 7).
(5)
Computer architecture
(Ref. Fig. 005)
Each unit (COM or MON) has the functions below:
-acquisition of digital inputs
-generation of digital outputs
-main processor
-
acquisition of discrete inputs
-
acquisition of analog inputs
-
generation of analog outputs (COM only)
-
generation of discrete outputs
-control of switching relays.
The acquisition of digital inputs and the generation of digital
outputs are performed by specific interfaces and by a specialized
processor located on the CDG and MDG boards.
The main processor (CPU and MPU boards) executes the servoloop
functions and calculates the laws.
It supplies the data required for the calculation of the laws and of
the logic to the slave processor (slave processing board, CSP and MSP
boards).
It communicates with the specialized processor of the digital input/
ouptut boards via a buffer memory.
The main processor directly manages the acquisition of the discrete
inputs.
1EFF : ALL 1 27-93-00Page 12 1 1 Feb 01/00R 1 1 1CES 1
中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱9(66)
