(2)
 Make sure that the access platform is in position at the access door

 822.

 (3)
 Make sure that the access door 822 is open.

 (4)
 On the battery power center 105VU:

 -make sure that the protective cover is removed.

 (5)
 Make sure that the side stick assembly is installed on the HOLDER -SIDE STICK (98D27303001001) (Ref. TASK 27-92-41-000-001).

 (6)
 Make sure that the PIN-SIDE STICK LOCKING (98D27903500000) is in position on the center universal joint of the side stick assembly.

 (7)
 Make sure that the warning notice which tells persons not to operate the side stick is in position on the side stick.

 1EFF : ALL 1 27-92-41Page 433 1 1 May 01/03R 1 1 1CES 1

 4. Procedure
_________
 (Ref. Fig. 406/TASK 27-92-41-991-005-A) Subtask 27-92-41-420-053
 A. Installation of the Side Stick Lock-Solenoid
 (1)
 Clean the component interface and/or the adjacent area.

 (2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Install the solenoid (64) on its support (62).

 (4)
 Install the washers (61), the screws (60) and tighten.

 (5)
 Safety the screws (60) with lockwire-corrosion resistant steel dia.

 0.8 mm (0.03 in.).

 (6)
 Remove the blanking caps from the electrical connectors.

 (7)
 Make sure that the electrical connectors are clean and in the correct condition.

 (8) Connect the electrical connector (63) to the solenoid (64). Subtask 27-92-41-480-055
 B. Installation of the Tools
 (1)
 Remove the PIN-SIDE STICK LOCKING (98D27903500000) from the side stick assembly.

 (2)
 Install the RIGGING PIN (98DNSA20206080) on the roll and pitch transducer units.

 (3)
 Disconnect the electrical connector (15).
 FOR 12CA1
 Disconnect the 2197VC
 FOR 12CA2
 disconnect the 2188VC
 (Ref. Fig. 402/TASK 27-92-41-991-002-A)

 (4)
 Put blanking caps on the disconnected electrical connectors.

 (5)
 Connect the 28 VDC POWER SUPPLY TOOL (355M03200001) to the electrical connector (15).

 1EFF : ALL 1 27-92-41Page 434 1 1 May 01/03R 1 1 1CES 1

 Subtask 27-92-41-010-059
 C. Remove the bellows (Ref. TASK 27-92-41-000-009). Subtask 27-92-41-820-050
 D. Adjustment of the Locking Mechanism in AP Mode
 (1)
 Energize the 28 VDC POWER SUPPLY TOOL (355M03200001) with a 28VDC external power supply.

 (2)
 Make sure that:

 (a)
 You can install a gauge 0.01 mm (0.0003 in.) to 0.02 mm (0.0007 in.) between the end of the rod (64) and the bellcrank (see the NOTE).

 (b)
 The rollers (68) are engaged on the cam (67) (see the NOTE).

 (c)
 You can remove and install freely the RIGGING PIN (98DNSA20206080) on the roll and pitch transducer units (see the NOTE).

 (d)
 The override loads are correct, as follows:

 1_ Remove the RIGGING PIN (98DNSA20206080) from the roll
 transducer unit.
 2_ With a dynamometer make sure that the override load in roll
 control is between 3.1 daN (6.9690 lbf). and 4.6 daN (10.3412
 lbf).
 3_ Install the RIGGING PIN (98DNSA20206080) on the roll
 transducer unit.
 4_ Remove the RIGGING PIN (98DNSA20206080) from the pitch
 transducer unit.
 5_ With the dynamometer, make sure that the override load in
 pitch control is between 4.5 daN (10.1164 lbf) and 6 daN
 (13.4885 lbf).
 NOTE : If you cannot get the above conditions, adjust the____
 length of the rod (66), as follows:
 - loosen the locknut (69) (only for solution 2)
 - turn the rod (66) in the correct direction
 - tighten the locknut (69) (only for solution 2)

 1EFF : ALL 1 27-92-41Page 435 1 1 May 01/03R 1 1 1CES 1

 -apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-007) on the locknut and the rod (66) (only for solution 2).
 (3)
 De-energize the 28 VDC POWER SUPPLY TOOL (355M03200001).

 (4)
 Put the control handle in the nose-up or in the nose-down configuration.

 (5)
 Make sure that the clearance J1 between the cam (67) and the rollers

 (68) is 0.2 mm (0.0078 in.) minimum.

 (6)
 Put the control handle in the neutral position.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱9(48)