-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
-
set the ND potentiometer to the - SELF TEST IN PROGRESS (MAX 40
B.
Test of Upper and lower ECAM Display Units (DU) Brigntness
center position. SECONDS) comes into view then the ND
image comes into view.
4. On the ND:
- point the beam of the flash - make sure that the image becomes
lights at the two brighter.
photo-electric cells at the
same time.
Subtask 31-60-00-710-057
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the ECAM control panel: - SELF TEST IN PROGRESS (MAX 40
- set the UPPER potentiometer to SECONDS) then the EWD image comes
the middle position. into view
2. On the upper ECAM DU:
- point the beam of the flash - make sure that the image becomes
lights at the two brighter.
photo-electric cells at the
same time.
3. On the ECAM display:
- set the LOWER DISPLAY - SELF TEST IN PROGRESS (MAX 40
potentiometer to the center SECONDS) then the SD image comes into
position. view.
4. On the lower ECAM DU:
- point the beam of the flash - make sure that the image becomes
lights at the two brighter.
photo-electric cells at the
same time.
1EFF : ALL 1 31-60-00Page 516 1 1 Aug 01/05R 1 1 1CES 1
5. Close-up
________ Subtask 31-60-00-860-059
A. Put the aircraft back to its initial configuration.
(1)
Do the EIS Stop Procedure (Ref. TASK 31-60-00-860-002)
(2)
Do the ADIRS Stop Procedure (Ref. TASK 34-10-00-860-005).
(3)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002)
(4)
Make sure that the work area is clean and clear of tool(s) and other items.
R 1EFF : ALL 1 31-60-00Page 517 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 401-499,
TASK 31-60-00-710-005
Operational Test of EFIS/ECAM Automatic and Manual Transfer
1. Reason for the Job
__________________
Refer to the MPD TASK: 315000-02
To make sure that these functions are correct:
-Automatic PFD/ND Transfer
-
Manual PFD/ND Transfer
-
Manual ECAM/ND Transfer
-
Manual DMC1 and DMC2 to DMC3 Switching
-Automatic SD/EWD Transfer
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power
31-60-00-860-001 EIS Start Procedure
31-60-00-860-002 EIS Stop Procedure
3. Job Set-up
__________
Subtask 31-60-00-860-092
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002)
(2)
Do the EIS Start procedure (Ref. TASK 31-60-00-860-001)
(3)
On the center pedestal, on the SWITCHING panel 8VU, make sure that all of the selector switches are at NORM.
R 1EFF : 401-499, 1 31-60-00Page 518 1 1 Aug 01/05 1 1 1CES 1 Subtask 31-60-00-865-070
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU EIS/ECAM/CTL/PNL 15WT E12
49VU EIS/DMC1/SPLY 10WT1 E11
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 7(81)
