REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R Material No. 19-003 USA AMS 3819
R LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R C. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 52-10-00-010-001 R 52-10-00-410-001 R 52-10-00-860-001 R R 52-10-00-860-002 R R SRM 512111,P.Block-001 R SRM 517512,P.Block-001 R 52-13-18-991-007
R 3. Job Set-up
__________
R Subtask 52-13-18-941-053
R A. Get Access Opening of the Passenger/Crew Door Closing of the Passenger/Crew Door Special Precautions before Work on the Passenger/Crew Door Special Precautions after Work on the Passenger/Crew Door
Fig. 805
R WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE
_______ R THAN 65 KNOTS.
R WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______ R - THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH R THE SAFETY PIN INSTALLED. R - THE PERCUSSION LEVER OF THE DOOR-DAMPER AND R EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH R THE SAFETY PIN INSTALLED.
R WARNING : STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES.
_______ R RESIDUAL PRESSURE COULD CAUSE THE DOOR TO OPEN WITH A SUDDEN R FORCE AND INJURE PERSONS AND/OR DAMAGE THE AIRCRAFT.
R (1) Put the access platform in position in the zone 832 or 842.
R (2) Open the door 832 or 842 (Ref. TASK 52-10-00-010-001).
1EFF : ALL 1 52-13-18Page 811 1 1 Aug 01/00 1 1 1CES 1
(3) Obey the special precautions before you start work on the door (Ref. TASK 52-10-00-860-001).
4. Procedure
_________
Subtask 52-13-18-340-053
A. Repair of the Rubbing Strip of the Cover Plate
(Ref. Fig. 805/TASK 52-13-18-991-007)
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Remove the defective rubbing strip.
(2)
Use a nonmetallic scraper and a stiff brush to remove the damaged sealant.
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ R THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(3)
Clean the repair area with CLEANING AGENTS (Material No. 11-003) or CLEANING AGENTS (Material No. 11-004). Use the minimum quantity of cleaning agent that is necessary to clean the area. Dry the area immediately with MISCELLANEOUS (Material No. 19-003).
(4)
Clean the surfaces with CLEANING AGENTS (Material No. 11-026).
(5)
If necessary, do the protection treatment and the paint coating repair on the cover plate with PRETREATMENT FOR PAINTING (Material No. 13-002) and STRUCTURE PAINTS (Material No. 16-001) (Ref. SRM 512111,P.Block-001) (Ref. SRM 517512,P.Block-001).
(6)
Use paper adhesive tapes to show the limits of the bonding areas on the cover plate.
(7)
Mix BONDING AND ADHESIVE COMPOUNDS (Material No. 08-018) with a spatula.
1EFF : ALL 1 52-13-18Page 812 1 1 May 01/01 1 1 1CES 1
R R AFT Passenger/Crew Door - Rubbing Strips Figure 805/TASK 52-13-18-991-007
1EFF : 1 1 1CES ALL 1 111 52-13-18 Page 813 Aug 01/00
R (8) Use a brush to apply a thin and constant layer of BONDING AND
R ADHESIVE COMPOUNDS (Material No. 08-018) to the cover plate.
R (9) Use a brush to apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-
R 018) to the neoprene side of the rubbing strip.
R (10) Let the adhesive cure until it is not tacky (evaporation of
R solvents).
R (11) Put the rubbing strip on the cover plate and make sure that it is in
R the correct position.
R (12) Apply pressure to all the surface of the rubbing strip. Make sure
R that there are no bubbles under the rubbing strip.
R (13) Remove the paper adhesive tapes.
R (14) Apply a bead of SEALANTS (Material No. 09-016) along the bottom edge
R of the rubbing strip.
R (15) For a better bonding, it is recommended to apply a constant pressure
R to all the surface of the rubbing strip during 24 hours.
R 5. Close-up________
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(111)
