R TASK 52-11-31-000-005 R Removal of the Girt-Bar Fitting Blanking-Plates R 1. Reason for the Job
__________________ R Self Explanatory R 2. Job Set-up Information
______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific circuit breaker(s) safety clip(s)
R No specific access platform 3.5 m (11 ft. 6 in.)
R 98D52103501000 1 BALLAST WEIGHT - PASSENGER CREW DOOR
R B. Consumable Materials
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. 11-004 USA MIL-T-81533
R 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
R (Ref. 20-31-00)
R Material No. 19-003 USA AMS 3819
R LINT-FREE COTTON CLOTH (Ref. 20-31-00)
R C. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 25-62-44-000-002 R 52-10-00-010-001 R 52-10-00-480-001 R R 52-10-00-480-001 R R 52-10-00-860-001 R R 52-11-31-000-003 Removal of the Escape-Slide Pack-Assembly Opening of the Passenger/Crew Door Installation of the Passenger/Crew Door Ballast Weight (98D52103501000) for Escape Slide Installation of the Passenger/Crew Door Ballast Weight (98D52103501000) for Escape Slide/Raft Special Precautions before Work on the Passenger/Crew Door Removal of the Girt Bar Fittings
1EFF : ALL 1 52-11-31Page 462 1 1 Aug 01/04 1 1 1CES 1 1EFF : ALL 1 52-11-31Page 463 1 1 Aug 01/04 1 1 1CES 1 **ON A/C 001-002,
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R 52-11-31-991-017 Fig. 414
R 52-11-31-991-018 Fig. 415
R 3. Job Set-up__________
R Subtask 52-11-31-010-060
R A. Get Access
R WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE_______
R THAN 65 KNOTS.
R WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:_______
R - THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH
R THE SAFETY PIN INSTALLED.
R - THE PERCUSSION LEVER OF THE DOOR-DAMPER AND
R EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH
R THE SAFETY PIN INSTALLED.
R WARNING : STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES._______
R RESIDUAL PRESSURE COULD CAUSE THE DOOR TO OPEN WITH A SUDDEN
R FORCE AND INJURE PERSONS AND/OR DAMAGE THE AIRCRAFT.
R (1) Put the access platform in front of the passenger/crew door 831
R (841).
R (2) Open the passenger/crew door 831 (841) (Ref. TASK 52-10-00-010-001).
R (3) Obey the special precautions before you start work on the door
R (Ref. TASK 52-10-00-860-001).
R Subtask 52-11-31-865-064
R B. Open, safety and tag this(these) circuit breaker(s):
R -------------------------------------------------------------------------------
R PANEL DESIGNATION IDENT. LOCATION
R -------------------------------------------------------------------------------
R 121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11
R 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10
R 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
Subtask 52-11-31-010-061
C. Removal of Components
(1)
Remove the escape slide (Ref. TASK 25-62-44-000-002).
(2)
Install the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-480-001).
(3) Remove the girt bar fittings (Ref. TASK 52-11-31-000-003). R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-11-31-010-061-A
C. Removal of Components
(1)
Remove the escape slide/raft (Ref. TASK 25-62-44-000-002).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(49)
