(a) The guide rollers (31) move off the guide fittings (32), (36) with the clearances below.
1 C1 is 0.2 mm (0.0078 in.) to 0.8 mm (0.0314 in.).
_
1EFF : ALL 1 52-13-00Page 527 1 1 May 01/05 1 1 1CES 1_
(3)
If the clearances C1 and C2 are not in the tolerances, adjust the guide fittings (32), (36) as specified below:
(a)
Open the door and identify the position of the serrations of the plates (37), (38) on the upper and lower guide fittings (32), (36).
(b)
Loosen the screws (40) and move the guide fittings (32), (36) to get the correct clearances C1 and C2.
(c)
Tighten the screws (40).
(4)
When the door is in the down position, make sure that:
(a)
The rollers (31) of the guide fittings (32), (36) turn freely.
(b)
The clearance C4 is 0.2 mm (0.0078 in.) to 1.5 mm (0.0590 in.).
(c)
The clearance C3 is 0.2 mm (0.0078 in.) minimum.
(d)
The clearance C5 is 3 mm (0.1181 in.) to 6 mm (0.2362 in.). NOTE : A clearance C5 of 3 mm (0.1181 in.) to 8 mm (0.3149 in.)
____
is permitted.
(e)
If the clearances C3 and C4 are not in the tolerances, adjust the upper and lower guide fittings (32), (36).
(5)
When the door is closed, make sure that the clearance C6 is 0.2 mm (0.0078 in.) between the rollers (31) and the stop screws (35).
R **ON A/C 062-099, 105-149, 151-199, 204-299, 301-399, 401-499,
Subtask 52-13-00-820-053-A
C. Check and Adjustment of Clearances between the Rollers and the Guide Fittings (Ref. Fig. 502A/TASK 52-13-00-991-005-A)
(1) Operate the door several times.
1EFF : ALL 1 52-13-00Page 528 1 1 Aug 01/05 1 1 1CES 1 (2) When the door is in the up position, make sure that:
(a) The guide rollers (31) move off the guide fittings (32), (36) with the clearances below.
1 C1 is 0.2 mm (0.0078 in.) to 0.8 mm (0.0314 in.).
_
2 C2 is 0.2 mm (0.0078 in.) to 2.2 mm (0.0866 in.).
_
(3)
If the clearances C1 and C2 are not in the tolerances, adjust the guide fittings (32), (36) as specified below:
(a)
Open the door and identify the position of the serrations of the plates (37), (38) on the upper and lower guide fittings (32), (36).
(b)
Loosen the screws (40) and move the guide fittings (32), (36) to get the correct clearances C1 and C2.
(c)
Make sure that the eccentric screws (39):
-fully seal the holes of the guide fittings (32) and (36),
-
are not above the rounded areas or spot-facing edges,
-
are not out of the outer contour of the fitting.
(d)
Tighten the screws (40).
(4)
When the door is in the down position, make sure that:
(a)
The rollers (31) of the guide fittings (32), (36) turn freely.
(b)
The clearance C4 is 0.2 mm (0.0078 in.) to 1.5 mm (0.0590 in.).
(c)
The clearance C3 is 0.2 mm (0.0078 in.) minimum.
(d)
The clearance C5 is 3 mm (0.1181 in.) to 6 mm (0.2362 in.). NOTE : A clearance C5 of 3 mm (0.1181 in.) to 8 mm (0.3149 in.)
____
is permitted.
(e)
If the clearances C3 and C4 are not in the tolerances, adjust the upper and lower guide fittings (32), (36).
(5)
When the door is closed, make sure that the clearance C6 is 0.2 mm (0.0078 in.) between the rollers (31) and the stop screws (35).
R 1EFF : 062-099, 105-149, 151-199, 204-299, 1 52-13-00Page 529 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105, 151-154, 201-207,
Subtask 52-13-00-820-054
D. Check in the Z Axis of the Door and Locking Hook Adjustment
R **ON A/C 001-049, 051-061, 101-104, 201-203,
(Ref. Fig. 502/TASK 52-13-00-991-005)
R **ON A/C 062-099, 105-105, 151-154, 204-207,
(Ref. Fig. 502A/TASK 52-13-00-991-005-A)
R **ON A/C 001-049, 051-099, 101-105, 151-154, 201-207,
(Ref. Fig. 508/TASK 52-13-00-991-019)
(1) Close the door.
(2) Make sure that:
(a) The clearance C6 between the rollers (31) and bolts (35) is 0.2 mm (0.0078 in.).
(b) The locking hook (41) is in contact with the roller (40).
(3) If the clearance C6 is not in the tolerances, do the adjustment below:
(a) Open the door.
(b) Remove the nuts (34), the adjustable washers (33), and the bolts (35).
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(63)
