A. Installation of the Girt Bar Fittings (Ref. Fig. 410/TASK 52-11-31-991-011, 411/TASK 52-11-31-991-012)
(1) Clean all the contact surfaces between components with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003) if necessary.
1EFF : ALL 1 52-11-31Page 439 1 1 Aug 01/05 1 1 1CES 1
Girt Bar Fitting Adjustment
Figure 411/TASK 52-11-31-991-012
1EFF : ALL 1 52-11-31 Page 440
1 1 May 01/98
1 1
1CES 1
(2) Put the girt bar fittings (110) (120) in position.
(3) Install the screws (111) (121).
R (4) Make sure that the peripheral clearance J1 is 4 +0 -0.5 mm (0.1574 +0.0000 -0.0196 in.).
R R NOTE : The peripheral clearance J1 value is applicable only before____ you tighten the screws (111) and (121).
(5) Adjust the position of the girt bar fittings (Ref. TASK 52-11-00-820-001).
(6) Tighten the screws (111) (121).
(7) Apply a bead of SEALANTS (Material No. 09-005) between the fittings (110) (120) and the plate assy blanking (112) (122).
(8) Apply SEALANTS (Material No. 09-005) on the head of the screws (111) and (121).
5. Close-up________
**ON A/C 001-002,
Subtask 52-11-31-410-056
A. Installation of Components
(1) Remove the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-080-001).
(2) Install the escape slide (Ref. TASK 25-62-44-400-001).
R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-11-31-410-056-A
A. Installation of Components
(1) Remove the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-080-001).
(2) Install the escape slide/raft (Ref. TASK 25-62-44-400-001).
1EFF : ALL 1 52-11-31Page 441 1 1 Aug 01/05 1 1 1CES 1R **ON A/C ALL
Subtask 52-11-31-865-058
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 13WN, 15WN, 48WV
Subtask 52-11-31-410-057
C. Close Access
(1)
Obey the special precautions after the work on the door (Ref. TASK 52-10-00-860-002).
(2)
Remove all the ground support equipment, the maintenance equipment, the standard and special tools and all other items.
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
(4)
Close the passenger/crew door 831 (841) (Ref. TASK 52-10-00-410-001).
(5)
Remove the access platform(s).
1EFF : ALL 1 52-11-31Page 442 1 1 May 01/98 1 1 1CES 1 TASK 52-11-31-000-004
Removal of the Roller and Proximity Switch Mechanism
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 3.50 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-42-00-861-001 Energize the Ground Service Network from the External Power 25-23-46-000-001 Removal of the Door Linings at the FWD Passenger/Crew
Doors 52-10-00-010-001 Opening of the Passenger/Crew Door 52-10-00-860-001 Special Precautions before Work on the Passenger/Crew
Door
**ON A/C 001-049, 051-056,
52-11-31-991-015 Fig. 412
R **ON A/C 057-099, 101-149, 151-199, 201-299, 301-399, 401-499,
52-11-31-991-015-A Fig. 412A
1EFF : ALL 1 52-11-31Page 443 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 52-11-31Page 444 1 1 Nov 01/00 1 1 1CES 1 Subtask 52-11-31-865-061
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(44)
