-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | EE | | | | | | | | | OD23 | 15.882 | 15.893 | | | 15.870 | | | | | (0.6252)| (0.6257)| | | (0.6252)| | | | | | | 0.000 | 0.036 | | | 0.0072 | | | | | (0.0000)| (0.0014)| | |(0.0028)| | ID22 | 15.893 | 15.918 | | | | 15.942 | | | | (0.6257)| (0.6266)| | | |(0.6281) | | |--------|---------|---------|---------|---------|---------|---------|--------| | FF | | | | | | | | | OD28 | 9.531 | 9.540 | | | 9.520 | | | | | (0.3752)| (0.3755)| | | (0.3748)| | | | | | | 0.000 | 0.032 | | | 0.064 | | | | | (0.0000)| (0.0012)| | |(0.0024)| | ID27 | 9.540 | 9.563 | | | | 9.584 | | | | (0.3755)| (0.3764)| | | |(0.3773) | | -------------------------------------------------------------------------------
1EFF : ALL 1 52-11-22Page 605 1 1 Feb 01/98 1 1 1CES 1

 Escape Slide Gearbox
 Figure 602/TASK 52-11-22-991-025
 1EFF :  ALL  1  52-11-22 Page 606 
1  1  Feb 01/98
 1  1
 1CES  1

 INTENTIONALLY BLANK

 1 1
52-11-22Page 607
1 1 Feb 01/98 1 1 1CES 1

 Percussion System
 Figure 603/TASK 52-11-22-991-026- 12 (SHEET 1)
 1EFF :  ALL  1  52-11-22 Page 608 
1  1  Feb 01/98
 1  1
 1CES  1

 Percussion System
 Figure 603/TASK 52-11-22-991-026- 22 (SHEET 2)
 1EFF :  ALL  1  52-11-22 Page 609 
1  1  Feb 01/98
 1  1
 1CES  1

 (3)
 If the wear of the bushes is not in the tolerances:

 (a)
 Replace the bushes (Ref. TASK 52-10-00-915-001).

 (b)
 Or replace the parts on which they are installed.

 (4)
 If the link assemblies (21), (24) and (25) are worn or unserviceable:

 (a) Replace the rod end of the link assemblies (21), (24) and (25).

 (5)
 If the eye end assembly (26) is worn or unserviceable:

 (a)
 Replace the eye end assembly (26). Subtask 52-11-22-220-056

 D. Inspection of the Flexible Control
 (Ref. Fig. 604/TASK 52-11-22-991-027)

 (1)
 Do a detailed visual inspection of the eye end assemblies (30) and

 (31) and the parts of the flexible control.

 (2)
 If the eye end assemblies (30) and (31) are worn or unserviceable:

 (a)
 Replace the eye end assemblies (30) and (31). Subtask 52-11-22-220-057

 E. Inspection of the Telescopic Forks and the Girt Bar Control Shaft
 (Ref. Fig. 605/TASK 52-11-22-991-028)

 (1) Do a detailed visual inspection of the bearings, the link assemblies (at rod level) and the parts of the telescopic forks and the girt bar control shaft.
 1EFF : ALL 1 52-11-22Page 610 1 1 Feb 01/98 1 1 1CES 1

 Flexible Control
 Figure 604/TASK 52-11-22-991-027
 1EFF :  ALL  1  52-11-22 Page 611 
1  1  Feb 01/98
 1  1
 1CES  1

 Telescopic Forks and Girt Bar Control Shaft
 Figure 605/TASK 52-11-22-991-028
 1EFF :  ALL  1  52-11-22 Page 612 
1  1  Feb 01/98
 1  1
 1CES  1

 (2) Make sure that the dimensions are correct.
 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | DD | | | | | | | | | OD43 | 14.980 | 14.994 | | | 14.959 | | | | | (0.5897)| (0.5903)| | | (0.5938)| | | | | | | 0.022 | 0.063 | | | 0.0126 | | | | | (0.0008)| (0.0014)| | |(0.0049)| | ID44 | 15.016 | 15.043 | | | | 15.085 | | | | (0.5911)| (0.5922)| | | |(0.59.38 | | |--------|---------|---------|---------|---------|---------|---------|--------| | DD | | | | | | | | | OD43 | 14.980 | 14.994 | | | 14.959 | | | | | (0.5897)| (0.5903)| | | (0.5938)| | | | | | | 0.022 | 0.063 | | | 0.0126 | | | | | (0.0008)| (0.0014)| | |(0.0049)| | ID45 | 15.016 | 15.043 | | | | 15.085 | | | | (0.5911)| (0.5922)| | | |(0.59.38 | | -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(33)