(f)
Install a new cotter pin (26).
(5)
Put the emergency control handle in the ARMED position.
R (6) Make sure that the travel J4 is 31 -0.5 +1 mm (1.2204 -0.0196 +0.0393 R in.).
1EFF : ALL 1 52-11-22Page 517 1 1 Feb 01/03 1 1 1CES 1
Escape Slide Travel
Figure 505/TASK 52-11-22-991-016
1EFF : ALL 1 52-11-22 Page 518
1 1 May 01/98
1 1
1CES 1
(7)
If the travel J4 is not in the tolerances, do the adjustment below:
(a)
Remove and discard the cotter pin (35).
(b)
Loosen the nut (33).
(c)
Adjust the radius R. To do this, adjust the position of the serrated bellcrank (31) to get the correct radius R.
(d)
Tighten the nut (33). NOTE : If it is necessary to install a new bolt (30) you must
____ drill a hole of 2 mm (0.0787 in.).
(e)
Install a new cotter pin (34).
(8)
Put the emergency control handle in the DISARMED position.
(9) Make sure that the clearance J5 is 5 mm (0.1968 in.) minimum. R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-11-22-820-052-A
E. Adjustment of the Escape Slide/Raft Girt-Bar Travel
(Ref. Fig. 505/TASK 52-11-22-991-016)
(1)
Put the outer and the inner control handles in the door locked down position.
(2)
Put the emergency control handle in the DISARMED position.
(3)
Make sure that the clearance J3 between the girt bar and the telescopic fork end is 0.8 +0 +1.2 mm (0.0314 +0.0000 +0.0472 in.).
(4)
If the clearance J3 is not in the tolerances, do the adjustment below:
(a)
Remove and discard the cotter pin (26).
(b)
Remove the nut (27), the washers (25) and (24) and the bolt (23).
(c)
Adjust the position L of the lower eye-end assembly (20) to get the correct clearance J3.
(d)
Install the bolt (23), the washers (24) and (25), the nut (27).
1EFF : ALL 1 52-11-22Page 519 1 1 Aug 01/05 1 1 1CES 1
(e)
TORQUE the nut (27) to between 0.3 and 0.35 m.daN (26.54 and
30.97 lbf.in).
If it is necessary to install a new bolt (23) drill a hole of
dia. 1.9 mm (0.0748 in.).
(f)
Install a new cotter pin (26).
(5)
Put the emergency control handle in the ARMED position.
(6)
Make sure that the travel J4 is 31 -0.5 +1 mm (1.2204 -0.0196 +0.0393 in.).
(7)
If the travel J4 is not in the tolerances, do the adjustment below:
(a)
Remove and discard the cotter pin (34).
(b)
Loosen the nut (33).
(c)
Adjust the radius R. To do this, adjust the position of the serrated bellcrank (31) to get the correct radius R.
(d)
Tighten the nut (33). NOTE : If it is necessary to install a new bolt (30) drill a hole
____
of 2 mm (0.0787 in.).
(e)
Install a new cotter pin (34).
(8)
Put the emergency control handle in the DISARMED position.
(9) Make sure that the clearance J5 is 5 mm (0.1968 in.) minimum.
**ON A/C ALL
Subtask 52-11-22-820-056
F. Adjustement of the Escape-Slide Release Mechanism R **ON A/C 001-002, 051-052,
(Ref. Fig. 501/TASK 52-11-22-991-014)
1EFF : ALL 1 52-11-22Page 520 1 1 May 01/05 1 1 1CES 1
**ON A/C ALL R Post SB 52-1097 For A/C 001-002,051-052, (Ref. Fig. 501A/TASK 52-11-22-991-014-A) **ON A/C ALL
(Ref. Fig. 506/TASK 52-11-22-991-022, 507/TASK 52-11-22-991-023)
(1)
Rig the emergency control handle in ARMED position with RIGGING PIN (98DNSA20206120).
(2)
Make sure that the clearances J6 and J7 between the girt bar (71) and the girt bar fittings (70) are as follows:
(a)
J6 is 0.2 mm (0.0078 in.) to 0.8 mm (0.0314 in.).
(b)
J7 is 0.5 mm (0.0196 in.) to 1.0 mm (0.0393 in.).
(3)
If the clearances are not in the tolerances, adjust as follows:
(a)
Remove the sealant around the girt bar fittings (81), (83) and the head of the screws (80), (82) with CLEANING AGENTS (Material No. 11-004) and MISCELLANEOUS (Material No. 19-003), loosen the screws (80), (82).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(30)
