(2)
Make sure that the dimensions are correct.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | CC | | | | | | | | | OD52 | 28.595 | 28.608 | | | 28.577 | | | | | (1.1257)| (1.1262)| | | (1.1250)| | | | | | | 0.000 | 0.054 | | | 0.108 | | | | | (0.0000)| (0.0021)| | |(0.0042)| | ID51 | 28.608 | 28.649 | | | | 28.868 | | | | (1.1262)| (1.1279)| | | |(1.1293) | | |--------|---------|---------|---------|---------|---------|---------|--------| | CC | | | | | | | | | OD57 | 25.411 | 25.420 | | | 24.396 | | | | | (1.0004)| (1.0007)| | | (0.9998)| | | | | | | -0.005 | 0.045 | | | 0.090 | | | | |-(0.0002)| (0.0017)| | |(0.0034)| | ID56 | 25-425 | 25.456 | | | | 25.486 | | | | (1.0009)| (1.0022)| | | |(1.0033) | | |--------|---------|---------|---------|---------|---------|---------|--------| | CC | | | | | | | | | OD61 | 7.941 | 7.950 | | | 7.930 | | |
1EFF : ALL 1 52-13-21Page 618 1 1 Feb 01/98 1 1 1CES 1 -------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | | (0.3126)| (0.3129)| | | (0.3122)| | | | | | | 0.000 | 0.032 | | | 0.0064 | | | | | (0.0000)| (0.0012)| | |(0.0025)| | ID60 | 7.950 | 7.973 | | | | 7.994 | | | | (0.3129)| (0.3138)| | | |(0.3147) | | |--------|---------|---------|---------|---------|---------|---------|--------| | CC | | | | | | | | | OD63 | 7.941 | 7.950 | | | 7.930 | | | | | (0.3126)| (0.3129)| | | (0.3122)| | | | | | | 0.000 | 0.032 | | | 0.0064 | | | | | (0.0000)| (0.0012)| | |(0.0025)| | ID62 | 7.950 | 7.973 | | | | 7.994 | | | | (0.3129)| (0.3138)| | | |(0.3147) | | |--------|---------|---------|---------|---------|---------|---------|--------| | CC | | | | | | | | | OD64 | 28.595 | 28.608 | | | 28.577 | | | | | (1.1257)| (1.1262)| | | (1.1250)| | | | | | | 0.000 | 0.054 | | | 0.108 | | | | | (0.0000)| (0.0021)| | |(0.0042)| | ID65 | 28.608 | 28.649 | | | | 28.868 | | | | (1.1262)| (1.1279)| | | |(1.1293) | | -------------------------------------------------------------------------------
(3)
If the wear of the bushes is not in the tolerances:
(a)
Replace the bushes (Ref. TASK 52-10-00-915-001).
(b)
Or replace the parts on which they are installed.
(4)
If the link assemblies (53), (54), (55) and (59) are worn or unserviceable:
(a) Replace the rod end of the link assemblies (53), (54), (55) and (59).
(5)
If the bearing (58) is worn or unserviceable:
(a) Replace the flange bearing assy.
1EFF : ALL 1 52-13-21Page 619 1 1 Feb 01/98 1 1 1CES 1
Locking Shaft Mechanism
Figure 606/TASK 52-13-21-991-028- 12 (SHEET 1)
1EFF : ALL 1 52-13-21 Page 620
1 1 Feb 01/98
1 1
1CES 1
Locking Shaft Mechanism
Figure 606/TASK 52-13-21-991-028- 22 (SHEET 2)
1EFF : ALL 1 52-13-21 Page 621
1 1 Feb 01/98
1 1
1CES 1
Subtask 52-13-21-220-057
G. Inspection of the Locking Hook and Safety Pin
(Ref. Fig. 607/TASK 52-13-21-991-029)
(1)
Do a detailed visual inspection of the bushes, the link assemblies (at rod level) and the parts of the locking hook and safety pin.
(2)
Make sure that the dimensions are correct.
-------------------------------------------------------------------------------| FIG. | ORIGINAL MANUFACTURING LIMITS | IN-SERVICE WEAR LIMITS | | DETAIL |---------------------------------------|----------------------------| | AND | DIMENSION | ASSEMBLY CLEARANCE| DIMENSION LIMITS | MAX. | | ITEM | MM (IN.) | MM (IN.) | MM (IN.) | ALLOW. | | NO. |-------------------|-------------------|---------|---------| CLEAR. | | | MIN. | MAX. | MIN. | MAX. | MIN. | MAX. |MM (IN.)| |--------|---------|---------|---------|---------|---------|---------|--------| | CC | | | | | | | | | OD71 | 14.183 | 14.194 | | | 14.182 | | | | | (0.5583)| (0.5588)| | | (0.5583)| | | | | | | 0.006 | 0.035 | | | 0.070 | | | | | (0.0002)| (0.0013)| | |(0.0026)| | ID70 | 14.200 | 14.218 | | | | 14.242 | | | | (0.5590)| (0.5597)| | | |(0.5607) | | |--------|---------|---------|---------|---------|---------|---------|--------| | GG | | | | | | | | | OD73 | 19.053 | 19.064 | | | 19.041 | | | | | (0.7501)| (0.7505)| | | (0.7496)| | | | | | | 0.006 | 0.048 | | | 0.096 | | | | | (0.0002)| (0.0018)| | |(0.0036)| | ID75 | 19.070 | 19.101 | | | | 19.125 | | | | (0.7507)| (0.7520)| | | |(0.7529) | | -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(139)
