(f)
 Pull the flexible control through the hole at the bottom of the door.

 (8) Disassembly of the flexible control (108).
 (a)
 Remove the washer (104).

 (b)
 Loosen and remove the nut (107).

 (c)
 Release the lockwasher (116).

 (d)
 Loosen the nut (115).

 (e)
 Remove the eye end assembly (117).

 (f)
 Remove the lockwasher (116) and the nut (115).

 (g)
 Remove the seal nut (114).

 (h)
 Loosen and remove the nut (113).

 (i)
 Remove the washer (112), the fitting (111) and the washer (110).

 (j)
 Loosen and remove the nut (109).

 (k) Remove the flexible control (108). Subtask 52-11-22-020-055
 E. Removal of the Girt Bar Control Shaft
 (Ref. Fig. 407/TASK 52-11-22-991-006)

 (1)
 Remove the nuts (142) the bolts (140) and the telescopic forks (143).

 (2)
 Remove the cotter pin (149) and discard it.

 (3)
 Remove the nut (148), the washers (150), (151), the bolt (153) and disconnect the flexible control cable (152).

 (4)
 Remove the nuts (146), (162), the washers (147), (163), the tapper pins (144), (165) and the levers (145), (164).

 1EFF : ALL 1 52-11-22Page 417 1 1 Nov 01/99R 1 1 1CES 1

 Telescopic Forks and Control Shaft of the Girt Bar Figure 407/TASK 52-11-22-991-006
 1EFF : 1 1R 1CES  ALL  1 11 1 52-11-22 Page 418 Nov 01/99

 (5)
 Remove the nuts (157), (158) the washers (156), (161) and the tapper pins (154), (160).

 (6)
 Disengage and remove the shaft (167) and remove the bellcrank (155) and the spacer (159).

 Subtask 52-11-22-020-050
 F. Removal of the Escape Slide Control Mechanism
 (Ref. Fig. 408/TASK 52-11-22-991-011)

 (1)
 Remove the cotter pin (193).

 (2)
 Remove the nut (194), the washer (192), the bolt (185), the washer

 (186) and disengage the rod (180).

 (3)
 Remove and discard the cotter pin (190).

 (4)
 Remove the nut (191), the washer (189), the bolt (187), the washer

 (188) and disengage the rod end (199).

 (5)
 Remove the rod end (199), the spring (200) and the bushing (201).

 (6)
 Remove the cotter pin (195).

 (7)
 Remove the nut (196), the washer (197), the bolt (181) and the washers (182), (183).

 (8)
 Remove the hook (198) and the spacer (184).

 1EFF : ALL 1 52-11-22Page 419 1 1 Nov 01/99R 1 1 1CES 1

 Escape Slide Control Mechanism Figure 408/TASK 52-11-22-991-011
 1EFF : 1 1R 1CES  ALL  1 11 1 52-11-22 Page 420 Nov 01/99

 TASK 52-11-22-400-001
 Installation of the Release Mechanism of the Emergency Escape Slide of the FWD Passenger/Crew Door
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific grease gun R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft)
 98DNSA20206120 2 RIGGING PIN
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004  USA MIL-PRF-23827 TYPE I
 SYNTH.ESTER BASED GREASE HIGH PRESSURE
 (Ref. 20-31-00)

 Material No. 04-017 USA A-A-59173 SILICONE GREASE (Ref. 20-31-00) Material No. 05-002 USA MIL-P-8116 PUTTY, ZINC CHROMATE GENERAL PURPOSE (Ref. 20-31-00)
 Material No. 09-019  USA AMS 3267/3
 LOW ADHESION CORROSION INHIBITING SEALANT
 (Ref. 20-31-00)

 Material No. 11-004  USA MIL-T-81533
 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM)
 (Ref. 20-31-00)

 Material No. 15-004  USA MIL-C-16173 GRADE 3
 CORROSION PREVENTIVE COMPOUND (Ref. 20-31-00)

 Material No. 15-007  AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
 1EFF : ALL 1 52-11-22Page 421 1 1 May 01/05 1 1 1CES 1
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(20)