(11)
TORQUE the nut (29) to between 0.3 and 0.35 m.daN (26.54 and 30.97 lbf.in).
NOTE : If you install a new bolt (37), drill a hole of 1.9 mm (0.0748
____
in.).
(12)
Install a new cotter pin (28).
(13)
Install the washer (12), the bolt (11). Connect the telescopic rod (10).
(14)
Install the washer (13) and the nut (14).
(15)
TORQUE the nut (14) to between 0.3 and 0.35 m.daN (26.54 and 30.97 lbf.in).
NOTE : If you install a new bolt (11), drill a hole of 1.9 mm (0.0748
____
in.).
(16)
Install a new cotter pin (15).
(17)
Rig the triple lever with RIGGING PIN (98DNSA20206120) and put the emergency control handle in the ARMED position.
(18)
Put the rod (9) in position and adjust its length if necessary.
1EFF : ALL 1 52-11-22Page 436 1 1 May 01/05R 1 1 1CES 1
(19)
Install the washer (36), the bolt (38) and connect the rod (9).
(20)
Install the washer (27) and the nut (26).
(21)
TORQUE the nut (26) to between 0.3 and 0.35 m.daN (26.54 and 30.97 lbf.in).
NOTE : If you install a new bolt (38), drill a hole of 1.9 mm (0.0748
____
in.).
(22) Install the new cotter pin (25).
(23) Remove the RIGGING PIN (98DNSA20206120).
Subtask 52-11-22-420-055
G. Installation of the Escape Slide Control Mechanism
(Ref. Fig. 408/TASK 52-11-22-991-011)
(1)
Put the hook (198) and the spacer (184) in position.
(2)
Apply a coat of COMMON GREASE (Material No. 04-004) on the bolt (181).
(3)
Install the washers (183), (182), (197), the nut (196) and tighten it.
NOTE : If you install a new bolt (181), drill a hole of 2.8 mm
____
(0.1102 in.).
(4) Install a new cotter pin (195).
(5) Put the rod (180) in position and adjust it as follows: R **ON A/C 001-002, 051-052,
(Ref. Fig. 411/TASK 52-11-22-991-017) **ON A/C ALL R Post SB 52-1097 For A/C 001-002,051-052, (Ref. Fig. 411A/TASK 52-11-22-991-017-A)
1EFF : ALL 1 52-11-22Page 437 1 1 May 01/05 1 1 1CES 1
Escape Slide Control Mechanism - Adjustment
Figure 411/TASK 52-11-22-991-017
R 1EFF : 001-002, 051-052, 1 52-11-22Page 438 1 1 May 01/05 1 1 1CES 1
Escape Slide Control Mechanism - Adjustment Figure 411A/TASK 52-11-22-991-017-A
R 1EFF : 1 1 1CES ALL 1 111 52-11-22 Page 439 May 01/05
INTENTIONALLY BLANK
R 1 1
52-11-22Page 440
1 1 May 01/05 1 1 1CES 1
**ON A/C ALL
(a)
Put the emergency control handle in the DISARMED position.
(b)
Install the washers (186), (192), the bolt (185) and the nut (194).
(c)
Adjust the length of the rod (180) to get the clearance J1 of 2 +0 +0.5 mm (0.0787 +0.0000 +0.0196 in.) between the hook (198) and the emergency control handle.
(d)
TORQUE the nut (194) to between 0.3 and 0.35 m.daN (26.54 and
30.97 lbf.in)
NOTE : If you install a new bolt (185), drill a hole of 1.9 mm
____
(0.0748 in.).
(6)
Install a new cotter pin (193).
(7)
Install the bushing (201) and the spring (200).
(8)
Apply a coat of COMMON GREASE (Material No. 04-004) on the axle of the rod end (199) and install it.
(9)
Put the rod end (199) in position.
(10)
Install the washers (188), (189), the bolt (187) and the nut (191).
(11)
TORQUE the nut (191) to between 0.3 and 0.35 m.daN (26.54 and 30.97 lbf.in).
NOTE : If you install a new bolt (187), drill a hole of 1.9 mm
____
(0.0748 in.).
(12) Install a new cotter pin (190).
1EFF : ALL 1 52-11-22Page 441 1 1 Nov 01/01R 1 1 1CES 1
5. Close-up
________ Subtask 52-11-22-820-053
A. Adjustment
(1)
Check the adjustment of the escape slide release mechanism (Ref. TASK 52-11-22-820-001).
(2)
Do an adjustment of the percussion bellcrank finger of the door damper and emergency operation cylinder (Ref. TASK 52-11-14-820-002).
(3)
Check the adjustement of proximity switch 4WN1 or 4WN2 (Ref. TASK 52-71-00-820-002).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(25)
