(a) The guide rollers (81) move off the guide fittings (82) and (86) with the clearances below:
1 C1 is 0.2 mm (0.0078 in.) to 0.8 mm (0.0314 in.).
_
2 C2 is 0.2 mm (0.0078 in.) to 2.2 mm (0.0866 in.).
_
1EFF : ALL 1 52-13-11Page 442 1 1 May 01/05 1 1 1CES 1
Adjustment of the Upper Connection Link Figure 412/TASK 52-13-11-991-017
R 1EFF : 1 1 1CES ALL 1 111 52-13-11 Page 443 Feb 01/04
(3)
If the clearances are not in the tolerances, adjust the guide
fittings (82) (86) as specified below:
(a)
Open the door and identify the position of the serrations of the plates (90) (89) and on the upper and lower guide fittings (82), (86).
(b)
Loosen the screws (80) and move the guide fittings (82) (86) to get the correct clearances C1 and C2.
(c)
Temporarily tighten the screws (80).
(4)
With the door in the down position, make sure that:
(a)
The rollers (81) of the guide fittings (82) and (86) turn freely.
(b)
The clearance C3 is 0.2 mm (0.0078 in.) minimum.
(c)
The clearance C4 is 0.2 mm (0.0078 in.) to 1.5 mm (0.0590 in.).
(d)
The clearance C5 is 3 mm (0.1181 in.) to 8 mm (0.3149 in.).
(e)
If the clearances C3 and C4 are not in the tolerances, adjust the upper and lower guide fittings (82), (86).
(5)
Tighten the screws (80).
(6)
Open the door.
(7)
Put the two shims (thickness 0.2 mm (0.0078 in)) in position in the upper guide fittings (82).
(8)
Close the door, and measure the dimension between the shim and the
roller (81).
(9)
Open the door, remove the nuts (84), the bolts (85) and the shims.
(10)
Adjust the thickness of the washer (83) until the roller (81) touches the shim when the door is closed.
(11)
Install the washer (83), the bolt (85) and the nuts (84), tighten them.
(12)
Install the two shims in the upper sliders (82).
(13)
Close the door (Ref. Fig. 403/TASK 52-13-11-991-005, 412/TASK 52-13-11-991-017)
R 1EFF : 001-049, 051-061, 101-104, 201-203, 1 52-13-11Page 444 1 1 May 01/05 1 1 1CES 1
(14)
Make sure that the screw (60) of the upper connection link (59) is not stressed when installed in its hole.
(15)
If the screw is stressed, modify the radius R of the upper connection link (54) as follows:
(a)
Disconnect the connection links (59) from each side of the yoke (54).
(b)
Remove the nuts (57), the washers (58), (61) and the bolts (60) and the washers (62).
(c)
Disengage the support arm (63) from the upper connection link.
(d)
Loosen the end of the upper connection link (59).
(e)
Adjust the thickness of the set of washers (64) on the upper connection link (59) to modify the radius R of the upper connection link (59).
(f)
Tighten the end of the upper connection link (59) and install the washers (62).
(g)
Install the support arm (63) on the upper and lower connection links (59).
(h)
Install the washers (61) and the bolts (60).
(i)
Install the washers (57) and the nuts (58).
(j)
TORQUE the nuts (57) to between 1.2 and 1.35 m.daN (106.19 and
119.46 lbf.in). R **ON A/C 062-099, 105-149, 151-199, 204-299, 301-399, 401-499,
Subtask 52-13-11-820-054-A
E. Check and Adjustment of the Clearances between the Rollers and the Guide Fittings (Ref. Fig. 403/TASK 52-13-11-991-005, 406A/TASK 52-13-11-991-011-A, 412/TASK 52-13-11-991-017)
(1) Operate the door several times.
1EFF : ALL 1 52-13-11Page 445 1 1 Aug 01/05 1 1 1CES 1 (2) With the door in the up position, make sure that:
(a) The guide rollers (81) move off the guide fittings (82) and (86) with the clearances below:
1 C1 is 0.2 mm (0.0078 in.) to 0.8 mm (0.0314 in.).
_
2 C2 is 0.2 mm (0.0078 in.) to 2.2 mm (0.0866 in.).
_
(3)
If the clearances are not in the tolerances, adjust the guide fittings (82) (86) as specified below:
(a)
Open the door and identify the position of the serrations of the plates (90) (89) and on the upper and lower guide fittings (82), (86).
