4. Procedure
_________
Subtask 52-13-12-020-053
A. Removal of the Door Support Arm
(Ref. Fig. 401/TASK 52-13-12-991-001)
(1)
Remove the screws (12) and the washers (13) from the supports. Do not remove the bonding leads (11).
(2)
Remove the support arm (1) as follows:
(a)
Remove and discard the cotter pins (2).
(b)
Release the lockwasher (7).
(c)
Remove the nuts (3) and the washers (4).
(d)
Hold the support arm (1).
R (e) Remove the bolts (8) and (15), the lockwasher (7) then the bushes R (5) and (16).
(f) Discard the lockwasher (7).
1EFF : ALL 1 52-13-12Page 402 1 1 May 01/01 1 1 1CES 1
R Support Arm on the Door Frame Side Figure 401/TASK 52-13-12-991-001
1EFF : 1 1 1CES ALL 1 111 52-13-12 Page 403 May 01/01
(g) Remove the support arm (1). NOTE : If necessary, remove the components from the support arm.
____
(3)
Remove the bush (9), the adjustment washer (10), then the bush (6). Subtask 52-13-12-020-054
B. Removal of the Door Buffer and the Door Unlocking Pushbutton Switch (Ref. Fig. 402/TASK 52-13-12-991-002)
(1)
Remove the nuts (27) and the screws (25).
(2)
Remove the door buffer (26).
(3)
Remove the nuts (24), the washers (22) and the screws (21).
(4)
Remove the fitting (20).
(5)
Remove the pushbutton switch (23) from the support arm. Subtask 52-13-12-020-055
C. Removal of the Door Stay Mechanism
(Ref. Fig. 403/TASK 52-13-12-991-003)
(1)
Remove and discard the four cotter pins (30).
(2)
Remove the four nuts (31) and the washers (32) from the pins (34).
(3)
Remove the door stay mechanism (33).
1EFF : ALL 1 52-13-12Page 404 1 1 Feb 01/98 1 1 1CES 1
Door Buffer and the Door Unlocking Handle
Figure 402/TASK 52-13-12-991-002
1EFF : ALL 1 52-13-12 Page 405
1 1 Feb 01/98
1 1
1CES 1
Door Stay Mechanism
Figure 403/TASK 52-13-12-991-003
1EFF : ALL 1 52-13-12 Page 406
1 1 Feb 01/98
1 1
1CES 1
TASK 52-13-12-400-001
Installation of the Support Arm, Door Buffer, Door Pushbutton Switch and Door Stay Mechanism
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00) Material No. 06-008 AI TNA 007-10006
LUBRICANT (Ref. 20-31-00)
1EFF : ALL 1 52-13-12Page 407 1 1 Aug 01/05R 1 1 1CES 1
C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
2 cotter pin 52-13-04 04B-290 2 cotter pin 52-13-04 04D-290
R 2 cotter pin 52-13-04 04E-290 7 lockwasher 52-13-04 04B-370 7 lockwasher 52-13-04 04D-370
R 7 lockwasher 52-13-04 04E-370 30 cotter pin 52-13-04 06 -010 51 bolt 52-13-04 05B-110 51 bolt 52-13-04 05H-110 57 cotter pin 52-13-04 05B-040 57 cotter pin 52-13-04 05H-040 61 washers 52-13-04 05B-100 61 washers 52-13-04 05H-100 62 washers 52-13-04 05B-150 62 washers 52-13-04 05H-150
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-28-00-912-004 Electrical Bonding of Components With Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)-
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(90)
