(25) and the bolt (24).

 (b)
 Apply BONDING AND ADHESIVE COMPOUNDS (Material No. 08-007A) on the thread of the bolt (24) before installation.

 (c)
 Do not tighten the bolt (24). You must adjust the locking pin (30).

 (5)
 Connection of the rod (33).

 (a)
 Install the bushes (38) and (40) with SPECIAL MATERIALS (Material No. 05-002), the rod (33), the washer (42) and the bolt (41).

 (b)
 Install the washer (43) and the nut (44).

 (c)
 TORQUE the nut (44) to between 0.3 and 0.35 m.daN (26.54 and

 30.97 lbf.in).

 (d)
 Install a new cotter pin (45). NOTE : If you install a new bolt (41), drill a hole of 1.9 mm

____ (0.0748 in.) for the cotter pin installation.
 (6) Adjustment of the safety pin. (Ref. Fig. 414/TASK 52-13-21-991-013)
 (a)
 With the door in the up position, make sure that the safety pin covers the shoulder of the bush located on the fitting (56), and that the clearance J10 is 0 -0.3 +0.3 mm (0.0000 -0.0118 +0.0118 in.).

 (b)
 With the door in the down position (door closed and locked), make sure that the clearance J11 between the frame structure and the safety pin is 4 -0.5 +0.5 mm (0.1574 -0.0196 +0.0196 in.).

 (c)
 If the clearances J10 and J11 are not in the tolerances, open the door and adjust as follows:

 1_ Remove the bolt (24), the adjustable washers (25) and (29) and
 the caps (26) (27) and (28).
 2_ Put new adjustable washers (25) and (29) and install them,
 with the caps (26) (27) and (28) and the bolt (24). 

R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-21Page 460 1401-499, 1Aug 01/05 1 1 1CES 1 3 TORQUE the bolt (24) to between 0.6 and 0.7 m.daN (53.09 and

_ 61.94 lbf.in).
 (7) Installation of the locking hook (2).
 (a) Install the locking hook.
 1 Put the door in the up position.

_ 2 Apply COMMON GREASE (Material No. 04-004) on the sliding part
_
 of the shouldered bush (4). 3 Install the shouldered bush (4), the bolt (15), the washer
_
 (14) and the nut (5). 4 TORQUE the nut (5) to between 1.2 and 1.35 m.daN (106.19 and
_
 119.46 lbf.in).
 5 Install a new cotter pin (6).

_ NOTE : If you install a new bolt (15), drill a hole of 2.7 mm
____ (0.1062 in.) for the cotter pin installation.
 (b) Connect the rod (48). 1 Install the bellow (50), the plate (51), the bolts (52) and
_
 the clamp (53). Do not tighten the clamp (53). 2 TORQUE the nuts (49) to between 0.35 and 0.45 m.daN (30.97 and
_
 39.82 lbf.in). 3 Install the bushes (10) and (11) with SPECIAL MATERIALS
_
 (Material No. 05-002), the washer (12) and the bolt (13). 4 Install the washer (9) and the nut (8).
_ 5 TORQUE the nut (8) to between 0.7 and 0.8 m.daN (61.94 and
_
 70.79 lbf.in).
 6 Install a new cotter pin (7).

_ NOTE : If you install a new bolt (13), drill a hole of 2 mm
____ (0.0787 in.) for the cotter pin installation.
R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-21Page 461 1401-499, 1Aug 01/05 1 1 1CES 1

 (c) Connect the rod (23).

 1_ Install the bushes (21) and (22) with SPECIAL MATERIALS
 (Material No. 05-002), the washer (17) and the bolt (16).
 2_ Install the washer (18) and the nut (29).
 3_ TORQUE the nut (19) to between 0.15 and 0.17 m.daN (13.27 and
 15.04 lbf.in).
 4_ Install a new cotter pin (20).
 NOTE : If you install a new bolt (16), drill a hole of 1.8 mm____
 (0.0708 in.) for the cotter pin installation.

 (8) Adjustment of the locking hook (52). (Ref. Fig. 415A/TASK 52-13-21-991-030-A)
 (a)
 Open the door.

 (b)
 Put two shims in the upper fittings located on the frame.

 (c)
 Close the door.

 (d)
 Make sure that the clearance M1 between the locking hook (52) and the roller (58) is 0.5 +0.3 -0.3 mm (0.0196 +0.0118 -0.0118 in.). If the clearance is not in the tolerances, do as follows:

 1 Turn the rod (48) one turn to make it shorter.
_ 2 Remove and discard the cotter pin (602) and remove the nut
_ (601).
 3 Pull out the bush (603) by 4 mm (0.1574 in.) to disengage it
_ from the stop flat (605).
 4 Turn the bush (603) by the required correction value:
_ -0.9, -0.6, +0.6, +1.5 or +1.2. Make sure that the bush (603) stays engaged with its slots in the eccentric yoke (604).
 NOTE : The slotted drive between the bush (603) and the
____ eccentric yoke (604) has a foolproofing device (one position only).
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM DOORS 艙門2(125)