R 1EFF : 001-049, 051-099, 101-105, 151-159, 1 57-51-00Page 685 1201-210, 1May 01/05 1 1 1CES 1
Outer-Wing Gear-Support RIB5 - Inboard and Outboard Faces
Figure 614/TASK 57-51-00-991-015
R 1EFF : 001-049, 051-099, 101-105, 151-159, 1 57-51-00Page 686 1201-210, 1May 01/05 1 1 1CES 1
5. Close-up
________
Subtask 57-51-00-865-101
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
R **ON A/C 001-049, 051-061, 101-103, 201-203,
Subtask 57-51-00-410-084
B. Close Access
(1) Close the applicable access panel:
-for the left wing, close 574AB
-for the right wing, close 674AB. R **ON A/C 062-099, 104-105, 151-159, 204-210,
Subtask 57-51-00-410-084-A
B. Close Access
(1) Install the applicable access panel:
-for the left wing, install 574AB
-for the right wing, install 674AB. R **ON A/C 001-049, 051-099, 101-105, 151-159, 201-210,
Subtask 57-51-00-860-059
C. Aircraft Maintenance Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.
(3)
Fully retract the flaps (Ref. TASK 27-50-00-866-009).
R 1EFF : 001-049, 051-099, 101-105, 151-159, 1 57-51-00Page 687 1201-210, 1May 01/05 1 1 1CES 1 Subtask 57-51-00-942-065
D. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-049, 051-099, 101-105, 151-159, 1 57-51-00Page 688 1201-210, 1May 01/05 1 1 1CES 1R **ON A/C ALL
TASK 57-51-00-200-006
Detailed Visual Inspection of Outer Wing Trailing Edge False Rear Spar Forward and Aft Faces
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575151-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific flashlight
No specific mirror
No specific safety barriers
No specific warning notices
No specific access platform 3 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-51-37-000-002 Removal of the Access Panels 573AB(673AB),
573BB(673BB), 573CB(673CB) 57-51-37-400-002 Installation of the Access Panels 573AB(673AB),
573BB(673BB), 573CB(673CB) ASRM 575100 (for corrective action) 57-51-00-991-016 Fig. 615
3. Job Set-up
__________
(Ref. Fig. 615/TASK 57-51-00-991-016)
Subtask 57-51-00-941-065
A. Safety Precautions
(1)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2)
Put the safety barriers in position.
