R  (5) Fill the clearance between the access panel (2) and the trailing edge 
R  of the wing skin with SEALANTS (Material No. 09-016). 
R  5. Close-up________ 
R  Subtask 57-51-37-942-053 
R  A. Removal of Equipment 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Remove the access platform(s). 
R  (3) Remove the safety barriers. 
R  (4) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (Ref. TASK 27-00-
R  00-080-002) from the flap/slat control lever. 
R  (5) Remove the warning notice(s).

 TASK 57-51-37-000-004
 Removal of the Access Panels 575AB/575BB/575CB/575DB/575EB/575FB/575GB/575HB (675AB/675BB/675CB/675DB/675EB/675FB/675GB/675HB)
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
R R Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
 No specific warning notice
 No specific adjustable access platform 4 m (13 ft. 1 in.)
 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER

R  B. Referenced Information 
R  -------------------------------------------------------------------------------
R  REFERENCE DESIGNATION 
R  -------------------------------------------------------------------------------
R  27-00-00-480-002 Installation of the Flap/Slat Control-Lever Locking 
R  Tool (98D27803000000) 
R  27-50-00-866-009 Retraction of the Flaps on the Ground 
R  57-51-37-991-005 Fig. 403 
R  3. Job Set-up__________ 
R  (Ref. Fig. 403/TASK 57-51-37-991-005) 
R  Subtask 57-51-37-941-056 
R  A. Safety Precautions 
R  (1) Put the warning notice in the cockpit to tell persons not to operate 
R  the flaps/slats. 
R  (2) Make sure that the flaps/slats are fully retracted (Ref. TASK 27-50-
R  00-866-009) and install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER 
R  (98D27803500001) (Ref. TASK 27-00-00-480-002) on the flap/slat 
R  control lever. 
R  Put the safety barriers in position. 
R  Subtask 57-51-37-010-054 
R  B. Get Access 
R  (1) Put the adjustable access platform below the applicable access panel, 
R  zone 575(675). 
R  4. Procedure_________ 
R  CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING_______ 
R  EDGE: 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. 
R  - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. 
R  - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. 
R  INCORRECT INSTALLATION CAN CAUSE DAMAGE.

R Lower Trailing Edge Access Panels - Rib 10 to Rib 22 R Figure 403/TASK 57-51-37-991-005- 14 (SHEET 1)
 1EFF : ALL 1 57-51-37Page 420 1 1 Aug 01/02 1 1 1CES 1R Lower Trailing Edge Access Panels - Rib 10 to Rib 22 R Figure 403/TASK 57-51-37-991-005- 24 (SHEET 2)

 1EFF : ALL 1 57-51-37Page 421 1 1 Aug 01/02 1 1 1CES 1R Lower Trailing Edge Access Panels - Rib 10 to Rib 22 R Figure 403/TASK 57-51-37-991-005- 34 (SHEET 3)

 1EFF : ALL 1 57-51-37Page 422 1 1 Aug 01/02 1 1 1CES 1R Lower Trailing Edge Access Panels - Rib 10 to Rib 22 R Figure 403/TASK 57-51-37-991-005- 44 (SHEET 4)
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM WINGS 機(jī)翼3(165)