R 1EFF : 301-399, 1 57-51-33Page 421 1 1 May 01/04 1 1 1CES 1
R (3) At the front mounting:
R (a) Install the hollow bolt (12).
R (b) Install the washer (13) and the nut (14).
R (c) TORQUE the nut (14) to between 11.0 and 12.2 m.daN (81.12 and
R 89.97 lbf.ft).
R (d) Safety the nut (14) with MISCELLANEOUS (Material No. 19-010).
R (e) Install the bolt (11), the new lockwasher (15) and the nut (16).
R (f) TORQUE the nut (16) to between 6.8 and 7.8 m.daN (50.14 and 57.52
R lbf.ft).
R (g) Safety the nut (16) with the lockwasher (15).
R (4) At the rear mounting:
R (a) Install the bush (8) and the hollow bolt (9).
R (b) Install the washer (7), the new lockwasher (6) and the nut (5).
R (c) TORQUE the nut (5) to between 15.3 and 16.3 m.daN (112.83 and
R 120.20 lbf.ft).
R (d) Safety the nut (5) with the lockwasher (6).
R (e) Install the bolt (10), the washer (4) and the nut (3).
R (f) TORQUE the nut (3) to between 14.5 and 15.5 m.daN (106.93 and
R 114.30 lbf.ft).
R (g) Install the new cotter pin (2).
R (5) Apply a thin layer of SEALANTS (Material No. 09-005) around:
R - the heads of the bolts (10) and (11)
R - the hollow bolts (9) and (12)
R - the nuts (3), (5), (14) and (16).
R 1EFF : 301-399, 1 57-51-33Page 422 1 1 May 01/04 1 1 1CES 1
**ON A/C ALL
5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-33-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the No.1 flap track actuator (Ref. TASK 27-54-49-400-001).
(3) Install the applicable inboard flap (Ref. TASK 27-54-61-400-001). **ON A/C 301-399,
Subtask 57-51-33-410-050-A
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the LH(RH) shroud box (Ref. TASK 57-51-15-400-001).
(3)
Install the No.1 flap track actuator (Ref. TASK 27-54-49-400-001).
(4) Install the applicable inboard flap (Ref. TASK 27-54-61-400-003). **ON A/C ALL
Subtask 57-51-33-942-050
B. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the access platform(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and
standard tools and all other items.
R 1EFF : ALL 1 57-51-33Page 424 1 1 May 01/05 1 1 1CES 1 TASK 57-51-33-000-002
Removal of the No.2 Flap Track Beam
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notices
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM WINGS 機(jī)翼3(141)
