Flap Track 1 and the Attachment Fittings - Location and Detail
Figure 612/TASK 57-51-00-991-013
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 57-51-00Page 668 1301-399, 1May 01/05 1 1 1CES 1
Flap Track 1 and the Attachment Fittings - Location and Detail
Figure 612A/TASK 57-51-00-991-013-A
R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 57-51-00Page 669 1401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C 001-049, 051-061, 101-103, 201-203, 301-399,
Subtask 57-51-00-210-053
B. Inspection
(1) Use a flashlight and a mirror to examine the items that follow for cracks, damage, corrosion and the correct condition:
-
the roller track
-
the forward and rear attachment fittings
-
the X strut
-
the flap carriage
-
the pendulum assembly.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
Subtask 57-51-00-210-053-A
B. Inspection
(1) Use a flashlight and a mirror to examine the items that follow for cracks, damage, corrosion and the correct condition:
-
the roller track
-
the forward and rear attachment fittings
-
the flap carriage
-
the pendulum assembly.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575100) for the
____
correct repair procedure.
**ON A/C ALL
5. Close-up
________ Subtask 57-51-00-410-064
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels (Ref. TASK 53-35-11-400-001):
-
for the left wing, install 191ET, 193AT
-
for the right wing, install 192ET, 194AT.
(3) Close the MLG doors (Ref. TASK 32-12-00-410-001). Subtask 57-51-00-865-100
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 57-51-00-860-055
C. Aircraft Maintenance Configuration
(1) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.
(2) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-51-00-942-063
D. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 57-51-00Page 671 1 1 May 01/04R 1 1 1CES 1
TASK 57-51-00-200-004
R Detailed Inspection of Inboard Flap, Inboard Actuator Drive-Arm, Drive Strut R and Outer Part of Trunnion, LH/RH
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575142-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific flashlight
No specific mirror
No specific safety barriers
No specific warning notices
No specific adjustable access platform 3 m (9 ft. 10 in.)
98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(97)
