3. Job Set-up
__________
Subtask 57-51-33-941-055
A. Safety Precautions
(1) Make sure the warning notices are in the cockpit to tell persons not to operate the flaps or slats.
(2) Make sure that the safety barriers are in position. R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-33-860-051
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Make sure that the applicable No.2 flap track fairings have been removed (Ref. TASK 57-55-11-000-001).
(2)
Make sure that the carriage has been removed from the applicable No.2 flap track beam (Ref. TASK 27-54-46-000-001).
(3)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed on the flap/slat control lever.
(4)
Make sure that the access platform is in position below the applicable No.2 flap track beam (1), zone 581 (681).
**ON A/C 301-399,
Subtask 57-51-33-860-051-A
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Make sure that the applicable No.2 flap track fairings have been removed (Ref. TASK 57-55-11-000-004).
(2)
Make sure that the carriage has been removed from the applicable No.2 flap track beam (Ref. TASK 27-54-46-000-001).
(3)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed on the flap/slat control lever.
(4)
Make sure that the access platform is in position below the applicable No.2 flap track beam (1), zone 581 (681).
**ON A/C ALL
Subtask 57-51-33-865-054
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
4. Procedure
_________
**ON A/C 301-399,
(Ref. Fig. 402/TASK 57-51-33-991-002-A)
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 403/TASK 57-51-33-991-003)
**ON A/C ALL
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-51-33-560-050
A. Preparation of a Replacement Component
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(2)
Apply a layer of SEALANTS (Material No. 09-001) to the shims (12).
(3)
Put in position all the shims (12) and the bearing pads (11) that you removed.
(4)
Install the bolts (9) and the nuts (13).
(5)
Install the studs (8) (with the washer (18) on the outboard stud), the washers (14) and the nuts (15).
(6)
TORQUE the nuts (15) to between 2.26 and 2.4 m.daN (16.66 and 17.69 lbf.ft).
(7)
Install the new cotter pins (16).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-51-33Page 439 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 301-399,
R Subtask 57-51-33-560-050-A
R A. Preparation of a Replacement Component
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______
R MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼3(145)
