TASK 27-31-31-004-022
 2.  Elevator Tab Removal____________________
 A.  Special Tools and Equipment
 (1)  Rig Pin (E-5) - 0.309/0.311-inch diameter, 6.7 |0.25 inches long (MS20392-4)
 NOTE: The rig pin is part of the rig pin kit F70207-69, -78 or -83.
____
 B.  Standard Tools and Equipment
 (1)
Heat gun - Capable of providing a minimum of to 250 -F heat.

 C.  
Consumable Materials

 (1)  
A00247 Sealant - BMS 5-95

 D.  
References

 (1)  
AMM 27-31-00/201, Elevator and Tab Control System

 (2)  
AMM 27-31-00/501, Elevator and Tab Control System

 (3)  
AMM 27-09-91/601, Flight Controls Surface

 E.  
Access

 (1)  
Location Zone
 711, 712 Elevator and Tab

 (2)  
Access Panels
 3801/3802 Tail Cone Access Door
 9143/9243 Removable Elevator Leading Edge Upper

 F.  
Procedure

 (1)
Open the access door 3802 and the access panel 9143R or 9143L.

 S 864-002

 (2)  
Do this task: "Remove the Pressure from the Elevator Hydraulic Systems A and B" (AMM 27-31-00/201).

 (3)  
Install the rig pin E-5 in the aft control quadrant.

 S 014-001
 S 494-003
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-31
 ALL  ú ú 01 Page 401 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
TAB PUSHROD ACCESS PANEL
ELEVATOR TAB HINGE LOCATION (4 PER TAB)
SEE B  TAB CONTROL
MECHANISM ELEVATOR TAB
ACCESS PANEL (SAME ON BOTTOM)
TAB PUSHRODS
SEE A
INBD
FWD
ELEVATOR
CHECKNUTS ELEVATOR TAB PUSHRODS ELEVATOR TAB
HINGE RETAINING SCREWS
A
FWD
ELEVATOR
STA
STA
121.79 STA
94.27
(HINGE 4) 66.74 STA ELEVATOR TAB
(HINGE 3)
39.22
(HINGE 2)
NOTE:____  LEFT SIDE SHOWN, RIGHT SIDE SIMILAR.  B  (HINGE 1) 
Figure 401 (Sheet 1) Elevator Tab Installation 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-31
 ALL  ú ú 01 Page 402 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
BONDING 
JUMPER  ELEVATOR TAB 
HINGE FITTING 
TAB PUSHROD 
AFT MOUNTING  ELEVATOR 
BOLT  HINGE BRACKET 
FWD  HINGE BOLT 

A 737-300/400/500MAINTENANCE MANUAL
ELEVATOR ELEVATOR

ALL HINGES)
HINGE FITTING
HINGE FITTINGS NO. 2, 3 AND 4
(SLIP HINGE)
B-B

Elevator Tab Installation
Figure 401 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-31
 ALL  ú ú 02 Page 403 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 024-005
 (4)  
Remove the elevator tab (Fig. 401):

 (a)  
If the same tab will be re-installed then do the following: 1) Make sure that the elevator tab meets the freeplay limits, (AMM 27-09-91/601).

 2)  While you move the elevator trailing edge down, align the projected center of the elevator trailing edge with the index mark within +/- 0.04 inch or less.
 3)  Measure and record the elevator tab position (ref 27-31-00/501) "Adjustment- Elevator and tab Control System", using single point method.
 4)  If elevator tab rods are fabricated from aluminum, ambient temperature must be recorded.
 (b)
If same tab is not to be re-installed then do the following:

 1)  Do this task to measure the elevator tab position and the ambient temperature (measured at a single point or at four hinge point locations): "Adjustment - Elevator and Tab Control System" (AMM 27-31-00/501).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(156)