曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

DIAMETER  MITTED PER-WEAR DIM.  MAX DIA ANCE CLEAR-
MIN  MAX 
1  BEARING  ID  0.3120  0.3125  0.3155  0.0035  X 
BOLT  OD  0.3110  0.3120  0.3106  X 
2  ROD END  ID  0.3120  0.3130  0.3160  0.0040 X  1 
BOLT  OD  0.3110  0.3120  0.3106 
3  BUSHING  ID  0.8735  0.8745  0.8779  0.0041 X
BOLT ASSY BUSHING  OD  0.8724  0.8738  0.8720  X 
4  BUSHING  ID  0.6245  0.6250  0.6280  0.0040 X 
BOLT  OD  0.6230  0.6240  0.6226  X 
5  ROD END  ID  0.6245  0.6250  0.6280  0.0040 X 
BOLT  OD  0.6230  0.6240  0.6226  X 
6  BUSHING  ID  0.9995  1.0000  1.0030  0.0040 X 
BOLT  OD  0.9980  0.9990  0.9955  X 
7  BEARING 3  ID  0.9995  1.0000  1.0030  0.0040 X 
BOLT  OD  0.9980  0.9990  0.9955  X 
8  BUSHING  ID  1.1960  1.1980  1.2080  0.0182 X 
BOLT ASSY BUSHING  OD  1.1888  1.1898  1.1884  X 
9  MANIFOLD BRACKET  ID  1.3560  1.3580  1.3670  0.0140 X 
BUSHING  OD  1.3510  1.3530  1.3420  2 

GET A BUSHING. DRILL THE HOLE IN THE ROD END TO MAKE A 0.0002 TO 0.0013 INCH INTERFERENCE FIT WITH THE BUSHING. THE MAXIMUM SIZE HOLE IN THE ROD END IS 0.4379 INCH. REAM THE BUSHING TO A 0.3120-0.3130 INCH DIAMETER.
ROTATE THE BUSHING 90 DEGREES IF IT IS NOT WORN IN THIS DIRECTION.
REPLACE THE BEARING WHEN THE RADIAL PLAY IS MORE THAN 0.005 INCH BECAUSE THE TEFLON FABRIC LINER IS WORN.
Rudder Power Control Unit Wear Limits
Figure 601 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-91
 ALL  ú ú 01 Page 604 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 STANDBY RUDDER ACTUATOR SHUTOFF VALVE - MAINTENANCE PRACTICES
_____________________________________________________________
 1.  General_______
 A.  The standby rudder actuator shutoff valve (referred to as the shutoff valve) and the leading edge standby drive shutoff valve are the same type of valve.
 B.  This procedure gives the instructions to replace the shutoff valve (with the valve motor attached). This procedure also gives the instructions to replace only the valve motor. You do not have to remove the valve from the modular package to remove the valve motor.
 TASK 27-21-94-002-045
 2.  Standby Rudder Actuator Shutoff Valve Removal (Fig. 201)_____________________________________________
 NOTE:  Use this procedure to replace the shutoff valve and the valve motor. To replace only the valve motor, use the removal and installation procedure for the valve motor.
 A.  References
 (1)  
27-21-00/201, Rudder and Rudder Trim Control System

 B.  
Access

 (1)  
Location Zones
 216 Left Main Wheel Well

 C.  
Prepare for the Removal

 S 862-052
 (1)  
Remove hydraulic power from the standby system (Ref 27-21-00/201).

 S 862-051

 (2)  
Open these circuit breakers and attach DO-NOT-CLOSE tags:

 (a)  
P6 panel,
 1) FLT CONTR
 2) STBY RUD

 D.  
Remove the Shutoff Valve

 (1)  
Disconnect the electrical connector from the valve motor.

 (2)  
Remove the four bolts that attach the valve to the modular package.

 S 022-055
 S 022-054
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-94
 ALL  ú ú 01 Page 201 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(78)