S 084-029

 (4)  
Install the rudder nose cover 9559 on the right side.

 (5)  
Install the access panels 9512 and 9514.

 (6)
Fill the hydraulic reservoirs if it is necessary (AMM 12-12-00/301).

 S 084-030
 S 614-031
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-91
 ALL  ú ú 02 Page 409 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 RUDDER POWER CONTROL UNIT - ADJUSTMENT/TEST
___________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is a task for the adjustment and a task for the functional test of the rudder power control unit (PCU).
 TASK 27-21-91-825-001
 2.  Rudder Power Control Unit Adjustment____________________________________
 A.  Special Tools and Equipment
 (1)  Rig Pin R-5 - 0.311 +0.000/-0.002 inch diameter, 6.7 |0.25-inches long (F70207-11)
 NOTE: The rig pin is a part of the kit F70207-69, -78, or -83.
____
 B.  References
 (1)  
27-21-00/201, Rudder Control System

 C.  
Access

 (1)  
Location Zone
 706 Vertical Stabilizer

 (2)  
Access Panels
 9512 TE Access Door
 9514 TE Access Door

 D.  
Adjust the Rudder Power Control Unit

 S 865-002
 (1)  
Supply hydraulic power systems A and B to the rudder system. (AMM 27-21-00/201).

 (2)  
Remove the access panels 9512 and 9514.

 (3)  
Install the rig pin R-5.

 S 215-005

 (4)  
Do a check on the location of the rudder trailing edge in relation to the tab on the rudder index plate (Fig. 501):

 S 015-003
 S 485-004
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-91
 ALL  ú ú 01 Page 501 ú Jul 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

RUDDER
FOR SMALL RUDDER TRAVEL MEASURE IN A HORIZONTAL RUDDER TABPLANE FROM THE LEFT EDGE INDEX OF THE TAB TO THE INBOARD PLATE CORNER OF THE RUDDER TRAILING EDGE. THIS IS APPLICABLE WITH THE RUDDER TO THE LEFT SIDE OR THE RIGHT SIDE.

B-B

RUDDER

Rudder Travel and Index Plate
Figure 501

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-91
 ALL  ú ú 02 Page 502 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 (a)  If the rudder aligns with the tab, tighten the two checknuts on the vernier control rod (Fig. 502).
 NOTE: Make sure the total number of threads that you can see
____ on the sleeve and the rod end is not more than 27 turns.
 (b)  If the rudder does not align with the tab but is not more than
 0.50 inch away from the nearest side of the tab,
 adjust the vernier control rod:
 1) Loosen the two checknuts on the vernier control rod.
 2) Turn the sleeve on the vernier control rod to move the

 rudder until it aligns with the tab. 3) Tighten the two checknuts on the vernier control rod.
 NOTE: Make sure the total number of threads that you can
____ see on the sleeve and the rod end is not more than 27 turns.
 (c)  If the rudder is more than 0.50 inch from the nearest side of the tab, adjust the vernier control rod: 1) Move the FLT CONTROL A and B switches to OFF.
 WARNING: MAKE SURE YOU REMOVE THE HYDRAULIC POWER BEFORE YOU
_______ DISCONNECT THE VERNIER CONTROL ROD FROM THE ACTUATOR INPUT CRANK. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 2)  Disconnect the vernier control rod from the center crank at
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(74)