B.  
References

 (1)
27-31-00/201, Elevator and Tab Control System

 (2)
27-31-00/501, Elevator and Tab Control System

 C.  
Access

 (1)  
Location Zone
 709 Area 9 Left Horizontal Stabilizer
 710 Area 10 Right Horizontal Stabilizer

DIM "B"  1  TRAMMEL BAR 
____NOTE: THE STABILIZER TRIM JACKSCREW IS SHOWN ZERO DEGREES WITH THE STABILIZER LEADING EDGE AT  FWD 
1 THE "B" DIMENSION IS MEASURED BETWEEN THE CENTER OF THE UPPER AND LOWER GIMBAL PINS 
Figure 501 Stabilizer Trim Jackscrew Setting 

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-44
 ALL  ú ú 01 Page 501 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

RIB
NO. 5
NO. 6
+0.03
0.03
-0.03
SEAL ELEVATOR TO BODY SEALS
+0.03
0.00
-0.00

TAIL
CONE
0.03
GAP
Elevator Seal Adjustment
Figure 502 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-44
 ALL  ú ú 01 Page 502 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
ADJUSTMENT SCREW TO ADJUST BULB

STABILIZER
ELEVATOR
Elevator Seal Adjustment
Figure 502 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-31-44
 ALL  ú ú 01 Page 503 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F04247
A
737-300/400/500MAINTENANCE MANUAL
 (2)  
Access Panels
 9107 Access Panel Trailing Edge, LH
 9207 Access Panel Trailing Edge, RH
 9108 Access Panel Trailing Edge, LH
 9208 Access Panel Trailing Edge, RH
 9109 Access Panel Trailing Edge, LH
 9209 Access Panel Trailing Edge, RH
 9149 Removable Elevator Leading Edge, LH
 9249 Removable Elevator Leading Edge, RH
 9150 Removable Elevator Leading Edge, LH
 9250 Removable Elevator Leading Edge, RH

 D.
Procedure

 S 865-001
 (1)  
Do this task: "Remove Elevator Hydraulic Systems A and B"
 (Ref 27-31-00/201).

 S 865-002

 (2)
Use the trammel bar to set the horizontal stabilizer B dimension at

 41.57 |0.01 inches.
 S 015-004
 (3)  
Remove the access panels 9107, 9108, 9109, 9149, and 9150, or 9207, 9208, 9209, 9249, and 9250.

 S 825-005

 (4)  
Adjust the elevator seals (Fig. 502):

 (a)  
Make sure the elevator trailing edge aligns with the index mark on the tail cone in 0.06 inch or less.

 (b)  
At the ribs No. 1, 3, or 5 of the stabilizer trailing edge (Fig. 502, View A); Adjust the flat seals on each side of the elevator hinge: 1) Loosen the mounting bolts. 2) Adjust the seal to have a clearance of 0.03

 +0.03/-0.03-inch between the seal and the hinge fitting. 3) Tighten the mounting bolts. 4) Make sure the clearance between the seal and the hinge
 fitting is 0.03 +0.03/-0.03 inch.
 (c)  
At the ribs No. 1, 2, 3, and 4 of the stabilizer trailing edge (Fig. 502, View B); Adjust the bulb seals along the edge of the elevator nose: 1) Loosen the mounting bolts. 2) Adjust the seal to have a clearance of 0.03 +/- 0.03 inch. 3) Tighten the mounting bolts. 4) Make sure the seal has a clearance of 0.03 +/- 0.03 inch.

 (d)  
At the ribs No. 2, 4, or 6 of the stabilizer trailing edge (Fig. 502, View C); Adjust the bulb seals at the elevator front spar: 1) Loosen the seal mounting bolts.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(172)