(a)
Tighten the fastener until it is engaged.
(b)
Loosen the fastener and tighten it to 65-75 pound-inches.
S 216-006
(2)
FASTENERS THAT ATTACH THE MAST FITTING ASSEMBLY TO THE ELEVATOR TAB; Do a check of the fasteners:
(a)
Tighten the fastener until it is engaged.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-31
ALL ú ú 02 Page 601 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b) Tighten the fastener to 20-25 pound-inches.
TASK 27-31-31-206-007
3. Elevator Tabs Inspection (Fig. 601)
________________________
A. References
(1)
AMM 27-31-31/401, Elevator Tabs
B.
Access
(1)
Location Zone
711, 712 Elevator and Tab
(2)
Access Panels 3801/3802 Tail Cone Access Door 9143/9243 Removable Elevator Leading Edge Upper
C.
Procedure
S 026-001
(1) Do this task: "Elevator Tab Removal" (AMM 27-31-31/401).
NOTE: Elevator Tab trailing edge play limits (AMM 27-09-91/601)
____ will take precedence over above wear limits.
Elevator Tab Wear Limits
Figure 601 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-31
ALL ú ú 02 Page 602 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
ELEVATOR
9. BUSHING/PIN
B
Elevator Tab Wear Limits
Figure 601 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-31
ALL ú ú 02 Page 603 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500
MAINTENANCE MANUAL
REF OVERHAUL MANUAL FOR REPAIR DIMENSION BETWEEN FLANGE FACINGS OF BUSHINGS IN HINGE FITTING DIMENSION ACROSS FLANGE FACES OF BUSHINGS IN BEARING PLATE
____ ELEVATOR TAB TRAILING EDGE PLAY LIMITS (27-09-91) SHALL TAKE PRECEDENCE OVER ABOVE WEAR LIMITS.
NOTE:
Elevator Tab Wear Limits
Figure 601 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-31
ALL ú ú 01 Page 604 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(2) S 216-002Examine the parts for worn areas: (a) Use a micrometer or a vernier caliper to measure the parts for the worn areas. (b) Compare the dimensions you measured with the permitted dimensions shown in Fig. 601. (c) Replace the parts that are not in the tolerance. (d) Install the parts.
(3) S 426-003Do this task: "Elevator Tab Installation" (AMM 27-31-31/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-31-31
ALL ú ú 02 Page 605 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
ELEVATOR TAB CONTROL MECHANISM - REMOVAL/INSTALLATION
_____________________________________________________
1. General_______
A. This procedure has two tasks, one for the removal and one for the installation of the elevator tab control mechanism (which is referred to as the "tab mechanism"). The procedure has these parts:
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(160)
