(b)
If necessary, remove and discard the lockwire from the locknut (10).
(c)
Loosen the locknut (10).
1EFF : ALL 1 27-51-44Page 611 1 1 May 01/04R 1 1 1CES 1
(d)
Adjust the nut (12) until you can install the PIN-SETTING. Make sure that you can see the threads of the rod-end (9) through the check hole. If you cannot see the threads of the rod-end (9) through the check hole, check the flap rigging (Ref. TASK 27-51-00-820-003).
(e)
Tighten the locknut (10).
(f)
Install the washer (13) and the nut (15).
(g)
Torque the nut (15) to between 1.1 and 1.7 m.daN (97.34 and
150.44 lbf.in).
NOTE : It is possible to have a clearance between the bush and
____
the strut attachment bracket.
(h)
Install a new cotter pin (14).
(i)
If you loosened the locknut (10), TORQUE it to between 5.1 and
5.9 m.daN (37.61 and 43.51 lbf.ft).
(j) Safety the locknut (10) with MISCELLANEOUS (Material No. 19-010).
(3)
Remove the PIN-SETTING from the inspection/setting hole in the interconnecting strut.
(4)
Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to:
-
the head of the bolt (16)
-
the nut (15)
-
the washer (13)
-
the cotter pin (14).
(5)
Do an operational test of the flap interconnecting strut and the flap-attachment failure-detection sensors (Ref. TASK 27-51-00-710-002).
Subtask 27-51-44-865-069
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
1EFF : ALL 1 27-51-44Page 612 1 1 May 01/04R 1 1 1CES 1
Subtask 27-51-44-710-058
D. Test
(1)
Get access to the flight controls (F/CTL) page of the MCDU (Ref. TASK 31-32-00-860-006).
(2)
Do this test of the flap interconnecting strut and the
flap-attachment failure-detection sensors:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the MCDU: On the MCDU:
1. Push (in) the line key < SFCC 1. - the MCDU shows the SFCC 1 page.
2. Push (in) the line key SYSTEM STATUS FLP >. - the MCDU shows the SFCC 1 SYSTEMSTATUS FLAP page. These subsequent messages must not occur: - FLP 1 NO SFCC 2 DATA CHECK WIRING &
SFCC 2
- FLP 1 FAULTY FLP 2 DATA CHECK SFCC
1 OR 2
- NO LGCIU 1 DATA CHECK WIRING TO FLP
1
- FLP LH PROX SNSR 1 MISADJUSTMENT
and FLP LH PROX SNSR 2 OR WIRING TO
LGCIU 2
- FLP LH PROX SNSR 1 OR WIRING TO
LGCIU 1
- FLP LH PROX SNSR 2 OR WIRING TO
LGCIU 2
- FLP RH PROX SNSR 1 MISADJUSTMENT
and FLP RH PROX SNSR 2 OR WIRING TO
LGCIU 2
- FLP RH PROX SNSR 1 OR WIRING TO
LGCIU 1
- FLP RH PROX SNSR 2 OR WIRING TO
LGCIU 2.
3. Push (in) the line key <RETURN. - the MCDU shows the SFCC 1 page.
4. Push (in) the line key <RETURN. - the MCDU shows the SYSTEM REPORT/TEST PAGE.
1EFF : ALL 1 27-51-44Page 613 1 1 May 01/04R 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
5.
Push (in) the line key < SFCC 2.
6.
Push (in) the line key SYSTEM STATUS FLP >.
Subtask 27-51-44-860-058-A
-
the MCDU shows the SFCC 2 page.
-
the MCDU shows the SFCC 2 SYSTEMSTATUS FLAP page. These subsequent messages must not occur:
-
FLP 2 NO SFCC 1 DATA CHECK WIRING & SFCC 1
-
FLP 2 FAULTY FLP 1 DATA CHECK SFCC 1 OR 2
-NO LGCIU 2 DATA CHECK WIRING TO FLP 2
-
FLP LH PROX SNSR 2 MISADJUSTMENT and FLP LH PROX SNSR 1 OR WIRING TO LGCIU 1
-
FLP LH PROX SNSR 1 OR WIRING TO
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(119)
