(3)
Install the lifting-lugs (12) in the flap.
(4)
Attach the hoisting sling to the hoist.
NOTE : The inboard flap weighs 114 kg (251 lb).
____
(5)
Use the hoist to put the hoisting sling in position over the flap.
(6)
Lower the hoisting sling so that it can be attached to the lifting-lugs (12).
(7)
Connect the hoisting sling to the lifting-lugs (12) with the forked connections (10) and the pip-pins (11). If necessary, adjust the turnbuckles (13) to get a correct lift angle of 20 degrees.
Subtask 27-50-00-480-052
B. Installation of the Outboard Flap Hoisting Sling
(1)
Remove the blanking caps from the flap.
(2)
Remove the pip-pins (11) and the lifting-lugs (12) from the HOISTING SLING - OUTBOARD FLAP (98A27508020001).
(3)
Install the lifting-lugs (12) in the flap.
(4)
Attach the hoisting sling to the hoist.
NOTE : The outboard flap weighs 125 kg (276 lb).
____
(5)
Use the hoist to put the hoisting sling in position over the flap.
(6)
Lower the sling so that it can be attached to the lifting-lugs (12).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-50-00Page 243 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(7) Connect the hoisting sling to the lifting-lugs (12) with the forked
connections (10) and the pip-pins (11). If necessary, adjust the
turnbuckles (13) to get a correct lifting angle of 20 degrees.
R **ON A/C 301-399,
R Subtask 27-50-00-480-051-A
R A. Installation of the Inboard Flap Hoisting Sling
R (1) Remove the blanking caps from the flap.
R (2) Remove the pip-pins (11) and the lifting-lugs (12) from the HOISTING
R SLING - INBOARD FLAP (98A27508005001).
R (3) Install the lifting-lugs (12) in the flap.
R (4) Attach the hoisting sling to the hoist.
R NOTE : The inboard flap weighs 201 kg (442 lb).____
R (5) Use the hoist to put the hoisting sling in position over the flap.
R (6) Lower the hoisting sling so that it can be attached to the
R lifting-lugs (12).
R (7) Connect the hoisting sling to the lifting-lugs (12) with the forked
R connections (10) and the pip-pins (11). If necessary, adjust the
R turnbuckles (13) to get a correct lift angle of 20 degrees.
R Subtask 27-50-00-480-052-A
R B. Installation of the Outboard Flap Hoisting Sling
R (1) Remove the blanking caps from the flap.
R (2) Remove the pip-pins (11) and the lifting-lugs (12) from the HOISTING
R SLING - OUTBOARD FLAP (98A27508020001).
R (3) Install the lifting-lugs (12) in the flap.
R (4) Attach the hoisting sling to the hoist.
R NOTE : The outboard flap weighs 205 kg (451 lb).____
R (5) Use the hoist to put the hoisting sling in position over the flap.
R (6) Lower the sling so that it can be attached to the lifting-lugs (12).
R R R (7) Connect the hoisting sling to the lifting-lugs (12) with the forked connections (10) and the pip-pins (11). If necessary, adjust the turnbuckles (13) to get a correct lifting angle of 20 degrees.
R **ON A/C ALL
5. Close-up________
Subtask 27-50-00-942-057
A. Removal of Equipment
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Remove the safety barriers.
(3) Remove the warning notice(s).
(4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 27-50-00-000-002
Removal of the Inboard and Outboard Flap Hoisting-Sling
WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______
NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(2)
