R - The nuts (5)
R - The bolts (6)
R - The flange of the universal joint (3)
R - The flange of the torque shaft (4).
R (d) Installation of the torque shaft 6204CM (6254CM)
R 1_ Put the universal joint (3) in the installation position. Make
R sure that the flange aligns with the torque shaft (4).
R 2_ Install the bolts (6) and the nuts (5). Tighten the nuts (5)
R with your hand.
R 3_ If necessary install the spacers.
R 4_ TORQUE the nuts (5) to between 1.02 and 1.24 m.daN (90.26 and
R 109.73 lbf.in).
R (e) Install the PIN RIGGING-FLAPS (TRACK 1) (1).
R 1_ Make sure that you can remove/install the rigging (1) pin
R easily.
R 2_ If you cannot remove/install the rigging pin (1) easily do the
R adjustment procedure again.
R (f) Make sure that:
R - You cannot see the spline engagement groove at the movable
R joint
R - The dimension "A" is a minimum of 6.5 mm (0.2559 in.) at the
R movable joint.
R (g) Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
R (Ref. TASK 27-50-00-000-003)
R Subtask 27-54-00-820-052
R B. Adjustment of the Flap Track No. 2
R (1) Install the PIN RIGGING FLAPS (2) at the track 2.
R (2) If you cannot install the PIN RIGGING FLAPS (2) easily, do the steps
R that follow:
R (a) Removal of the Torque Shaft 6210CM (6260CM)
R 1_ Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
R PIVOT (98D27504030001) on a flap torque shaft, outboard of the
R component that you will remove (Ref. TASK 27-50-00-400-003).
R 2_ Remove the nuts (5) and the bolts (6) from the torque shaft
R (4).
R 3_ Remove the universal joint (3).
R (b) Adjustment of the flap drive system (for free rigging pin).
R 1_ Loosen the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
R PIVOT as necessary to turn the torque shafts.
R 2_ Turn the torque shaft 6218CM (6268CM) four turns in the
R extension direction.
R a_ Turn the torque shaft 6218CM (6268CM) in the retraction
R direction until the rigging pin (2) can be installed
R easily.
R b_ If the torque shaft 6218CM (6268CM) is accidentally turned
R too far in the retraction direction:
R - Do the adjusment procedure again, until the rigging pin
R (2) can be installed easily.
R (c) Preparation for Installation
R CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT._______
R GREASE AND ASSEMBLY PASTE DO NOT MIX.
R WARNING : USE A PROTECTIVE EYE SHIELD/GOGGLES WHEN YOU USE_______
R COMPRESSED AIR. DEBRIS AND/OR HIGH PRESSURE AIR CAN
R DAMAGE YOUR EYES.
R WARNING : DO NOT PUT COMPRESSED GAS IN CONTACT WITH YOUR SKIN._______
R THE GAS CAN GO THROUGH THE SKIN AND MAKE BUBBLES IN THE
R BLOOD. THIS CONDITION CAN KILL YOU.
R WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER_______
R SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR.
R OBEY THE MANUFACTURERS INSTRUCTIONS.
R PUT ON PROTECTIVE CLOTHING.
R DO NOT GET THEM IN YOUR MOUTH.
R DO NOT SMOKE.
R DO NOT BREATHE THE GAS.
R THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN
R IRRITANT.
R GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
R 1_ Use a clean lint-free cotton cloth MISCELLANEOUS (Material No.
R 19-003) and the cleaning agent CLEANING AGENTS (Material No.
R 11-026) to clean the parts that follow:
R - The nuts (5)
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(153)
