(d)
 Apply an up force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.

 NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-00Page 683 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 (e)
 Hold the flap in this position, measure and record the dimension Y and then release the flap.

 (f)
 To find the total free movement, subtract the dimension Z from the dimension Y.

 (10)
 At the track 4 position, measure the total free movement of the actuator lever (dimension X):

 (a)
 Apply a down force (by hand) to the actuator lever. Apply sufficient force to make the actuator lever move through possible free movement in the flap system mechanism and joints.

 (b)
 Hold the actuator lever in this position, then measure and record the dimension T.

 (c)
 Apply an up force (by hand) to the actuator lever. Apply sufficient force to make the actuator lever move through possible free movement in the flap system mechanism and joints.

 (d)
 Hold the actuator lever in this position, then measure and record the dimension S.

 (e)
 To find the total free movement (dimension X), subtract the dimension S from the dimension T.

 (11)
 Install the aluminum pin through the joint where you removed the bolt (212).

 (12)
 Retract the flaps fully (Ref. TASK 27-50-00-866-009).

 (13)
 Remove the aluminum pin.

 (14)
 At the track 4 position, temporarily connect the flap drive arm to the rotary actuator drive-lever as follows:

 (a)
 Install the bolt (212), the washer (213) and the nut (214).

 (b)
 Hand tighten the nut (214).

 (15)
 Compare the measured free movement dimensions:

 -the maximum acceptable value of free movement at the outboard flap trailing edge at tracks 3 and 4 is 11.0 mm (0.4330 in.)
 -for the maximum acceptable value of dimension X (free movement of the lever arm) refer to the table 601.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-00Page 684 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C 301-399,

 Subtask 27-54-00-220-057-A
 B. Detailed Dimensional Check - Free Movement at the Trailing Edge of the Outboard Flap
 (1) At the track 3 position, disconnect the outboard flap drive-arm from the rotary actuator lever-arm:
 (a)
 Remove and discard the cotter pin (231).

 (b)
 Remove the nut (230) and the washer (229).

 (c)
 Remove the bolt (226) and install the aluminum pin (20.0 mm (0.7874 in.) diameter).

 NOTE : The diameter of the aluminum pin is approximately 6.0 mm
____ (0.2362 in.) less than the bolt (226) it replaces. The pin is 100 mm (3.9370 in.) long and is made locally from material LN 1798 3.1354T3511. The pin is temporary and has two functions:
 -
it keeps the joint together when you extend/retract the flaps

 -
it is easy to remove the pin to disconnect the joint when the flaps are extended.

 (d)
 Extend the flaps fully (Ref. TASK 27-50-00-866-008).

 (e)
 Remove the aluminum pin.

 (2) At the track 4 position, measure the total free movement of the flap trailing edge:
 (a)
 Make sure that the flaps are fully extended, and that the travel ranges are clear.

 (b)
 Apply a down force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.

 NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
R 1EFF : 301-399, 1 27-54-00Page 685 1 1 May 01/05 1 1 1CES 1

 (c)
 Hold the flap in this position and measure and record the
 dimension Z.

 (d)
 Apply an up force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.

 NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
 (e)
 Hold the flap in this position, measure and record the dimension Y and then release the flap.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(176)