(c) Safety the outboard flap forward eccentrics (Ref. TASK 27-54-62-400-001).
 (Ref. Fig. 519A/TASK 27-51-00-991-069-B)
 (2)
 At the track 3 position, remove the KIT-FLAP RIGGING:

 (a)
 Remove the scale block (20).

 (b)
 Remove the pin (22) and remove the fin (21) from the base assembly (23).

 (c)
 Loosen the knurled screws (27) and remove the base assembly (23) from the flap track beam (28).

 (3)
 Measure the clearance of the flap guide-roller and adjust if necessary (Ref. TASK 27-54-63-400-001).

 **ON A/C 051-052,
 Subtask 27-51-00-820-074-C
 F. Complete the adjusment of the Rigged Position of the Outboard Flap (Ref. Fig. 520A/TASK 27-51-00-991-070-B)
 (1) If applicable, adjust the forward eccentrics back to the value shown on the label (41) at track 3. Adjust the forward eccentrics at track 3 and track 4 in sequence (in small increments).
 NOTE : Label (41) shows the assymetric offset value. This is the
____ adjustment applied to the forward eccentric bearing in the flap drive strut at tracks 3 and 4. The adjustment is necessary on some aircraft to give the correct aerodymamic balance:
 -
a plus (+) value shows that the flap trailing edge must be moved up

 -
a minus (-) value shows that the flap trailing edge must be moved down

R 1EFF : 002-049, 051-061, 101-105, 201-203, 1 27-51-00Page A548 1 1 Aug 01/05 1 1 1CES 1

 -a zero (0) value shows that no adjustment is necessary. (Ref. Fig. 522B/TASK 27-51-00-991-072-B)
 (a)
 At the track 3 position:

 (b)
 At the track 4 position: 1 Align the top surface of the flap with the line on the scale

 1_ Align the top surface of the flap with the line on the scale
 block (20) which agrees with:
 - the assymetric rigging value from the track 3 label (41).
 NOTE : The scale block has 1 millimeter graduations.____

_ block (20) which agrees with:
 -the calibration value (from track 4 label (42) plus or minus the assymetric rigging value from the track 3 label (41).
 NOTE : The scale block has 1 millimeter graduations.
____
 (c) Safety the outboard flap forward eccentrics (Ref. TASK 27-54-62-400-001).
 (Ref. Fig. 519B/TASK 27-51-00-991-069-A)
 (2)
 At the track 3 and track 4 positions, remove the KIT-FLAP RIGGING:

 (a)
 Remove the scale block (20).

 (b)
 Remove the pin (22) and remove the fin (21) from the base assembly (23).

 (c)
 Loosen the knurled screws (27) and remove the base assembly (23) from the flap track beam (28).

 (3)
 Measure the clearance of the flap guide-roller and adjust if necessary (Ref. TASK 27-54-63-400-001).

R 1EFF : 051-052, 1 27-51-00Page A549 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,

 Subtask 27-51-00-820-074-B
 F. Complete the Adjustment of the Rigged Position of the Outboard Flap
 **ON A/C 062-099, 151-153, 204-207,
 (Ref. Fig. 520/TASK 27-51-00-991-070)

R **ON A/C 106-149, 154-199, 208-299, 401-499,
 (Ref. Fig. 520B/TASK 27-51-00-991-070-A)
R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
 (1) If applicable, adjust the forward eccentrics back to the value shown on the label (41) at track 3. Adjust the forward eccentrics at track 3 and track 4 in sequence (in small increments).
 NOTE : Label (41) shows the assymetric offset value. This is the
____ adjustment applied to the forward eccentric bearing in the flap drive strut at tracks 3 and 4. The adjustment is necessary on some aircraft to give the correct aerodymamic balance:
 -
a plus (+) value shows that the flap trailing edge must be moved up

 -
a minus (-) value shows that the flap trailing edge must be moved down

 -
a zero (0) value shows that no adjustment is necessary.

 (Ref. Fig. 522B/TASK 27-51-00-991-072-B)
 (a) At track 3 and track 4:
 1 For a '+' value, the top surface of the flap must align (+/-
_ 1.0 mm (0.0393 in.)) with:
 -the line above zero on the scale block (20) which is the same as the label value.
 2 For a '-' value, the top surface of the flap must align (+/-
_ 1.0 mm (0.0393 in.)) with:
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-51-00Page A550 1401-499, 1Aug 01/05 1 1 1CES 1

 -the line below zero on the scale block (20) which is the same as the label value.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(71)