B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 27-50-00-991-001 Fig. 204
 **ON A/C 301-399,

 27-50-00-991-001-A Fig. 204A **ON A/C ALL

 3. Job Set-up
__________
 Subtask 27-50-00-941-057

 A. Safety Precautions
 (1)
 Make sure that the safety barriers are in position.

 (2)
 Make sure that the warning notice is in position to tell persons not to operate the flap/slat control lever.

 4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 (Ref. Fig. 204/TASK 27-50-00-991-001)
 **ON A/C 301-399,

 (Ref. Fig. 204A/TASK 27-50-00-991-001-A)
 **ON A/C ALL

 Subtask 27-50-00-080-051
 A. Removal of the Inboard Flap Hoisting Sling
 (1)
 Remove the pip-pins (11) and disconnect the hoisting sling from the inboard flap.

 (2)
 Remove the lifting-lugs (12) from the inboard flap and connect them to the hoisting sling with the pip-pins (11).

 (3)
 Remove the HOISTING SLING - INBOARD FLAP (98A27508005001) from the hoist.

 (4)
 Install the blanking caps in the flap. Make sure that the top of the blanking caps are not above the surface of the flap.

 Subtask 27-50-00-080-052
 B. Removal of the Outboard Flap Hoisting Sling
 (1)
 Remove the pip-pins (11) and disconnect the hoisting sling from the outboard flap.

 (2)
 Remove the lifting-lugs (12) from the outboard flap and connect them to the hoisting sling with the pip-pins (11).

 (3)
 Remove the HOISTING SLING - OUTBOARD FLAP (98A27508020001) from the hoist.

 (4)
 Install the blanking caps in the flap.

 5. Close-up
________ Subtask 27-50-00-942-058
 A. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the safety barriers.

 (3)
 Remove the warning notice(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 27-50-00Page 248 1 1 May 01/04R 1 1 1CES 1

 TASK 27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and Slats (98D27504030001) WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice 98D27504030001 1 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-991-004 Fig. 205
 1EFF : ALL 1 27-50-00Page 249 1 1 May 01/04R 1 1 1CES 1

 3. Job Set-up
__________ Subtask 27-50-00-941-058
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put a warning notice in position, on panel 114VU to tell persons not to operate the flap/slat control lever.

 4. Procedure
_________ (Ref. Fig. 205/TASK 27-50-00-991-004) Subtask 27-50-00-480-050
 A. Installation of the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001)
 (1)
 Make sure that the protective pads on the items that follow are in a satisfactory condition.

 -
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(3)