Label Position - Flap Track Beam
Figure 511B/TASK 27-51-00-991-060-B
R 1EFF : 301-399, 1 27-51-00 Page 582
1 1 May 01/05
1 1
1CES 1
Outboard Flap Rigging Dimensions (Sheet 1)
Figure 512/TASK 27-51-00-991-058
R 1EFF : 002-049, 053-061, 101-105, 201-203, 1 27-51-00Page 583 1 1 May 01/05 1 1 1CES 1
Outboard Flap Rigging Dimensions
Figure 512A/TASK 27-51-00-991-058-A
R 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-51-00Page 584 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1
Outboard Flap Rigging Dimensions
Figure 512B/TASK 27-51-00-991-058-B
R 1EFF : 301-399, 1 27-51-00 Page 585
1 1 May 01/05
1 1
1CES 1
Outboard Flap Rigging Dimensions (Sheet 2)
Figure 513/TASK 27-51-00-991-059
R 1EFF : 002-049, 053-061, 101-105, 201-203, 1 27-51-00Page 586 1 1 May 01/05 1 1 1CES 1
(c) If the value on the label (42) shows a plus value, subtract this value from the dimension shown on the scale block (42). The remaining value must be zero +/- 4 mm (0.16 in.).
(d) If the value on the label (42) shows a minus value, add this value to the dimension shown on the scale block (41). The remaining value must be zero +/- 4 mm (0.16 in.).
(2) At the outboard end of the flap, measure:
(a) The dimension S (the vertical measurement between the fixed shroud and the outboard end of the flap):
1_ Check the value shown on the label (42) attached to the outboard side of the flap track 3 beam.
2_ If the value on the label (42) is '0', the dimension S must be zero +/- 2 mm (0.08 in.).
3_ If the value on the label (42) shows a plus value, subtract the value from the dimension S. The remaining value must be zero +/- 2 mm (0.08 in.).
4_ If the value on the label (42) shows a minus value, add the value to the dimension S. The remaining value must be zero +/-2 mm (0.08 in.).
(3) If the flap rigged position is not correct, adjust as necessary until the flap is in the specified limits (Ref. TASK 27-51-00-820-008).
R **ON A/C 051-052,
R Subtask 27-51-00-220-057-E
R R C. To Do a Check of the Outboard Flap Rigged Position (Ref. Fig. 512A/TASK 27-51-00-991-058-A, 514/TASK 27-51-00-991-065)
R R R R NOTE : The tolerances given in the work steps that follow are in-service____ tolerances only. They are not initial adjustment tolerances. The tolerances for initial adjustment are given in the flap rigged position adjustment procedure (Ref. TASK 27-51-00-820-008).
R R NOTE : The scale must be read from the outboard side of the flap track____ beam.
R 1EFF : 002-049, 051-061, 101-105, 201-203, 1 27-51-00Page 587 1 1 May 01/05 1 1 1CES 1
R Label Positions - Flap Track Beams
R Figure 514/TASK 27-51-00-991-065
R 1EFF : 051-052, 1 27-51-00 Page 588
1 1 May 01/05
1 1
1CES 1
R (1) At the track 3 position, make sure that the top surface of the
R trailing edge aligns with the scale block (41) as follows:
R (a) Check the value shown on the label (42) attached to the outboard
R side of the flap track 3 beam.
R (b) If the value on the label (42) is '0', make sure that the
R trailing edge aligns with the zero mark +/- 4 mm (0.16 in.).
R (c) If the value on the label (42) shows a plus value, subtract this
R value from the dimension shown on the scale block (41). The
R remaining value must be zero +/- 4 mm (0.16 in.).
R (d) If the value on the label (42) shows a minus value, add this
R value to the dimension shown on the scale block (41). The
R remaining value must be zero +/- 4 mm (0.16 in.).
R NOTE : The scale must be read from the outboard side of the flap____
R track beam.
R (2) At the track 4 position the top surface of the trailing edge must
R align with the scale block (41) as follows:
R (a) Check the value shown on the label (42) attached to the outboard
R side of the flap track 3 beam.
R (b) Check the calibration value on the label (43) on the outboard
R side of flap track 4.
R (c) The trailing edge must align with the line on the scale which
R agrees with:
R - the calibration value from label (43) plus or minus the
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(58)
