Universal joints let the torque shafts have large angular changes of
alignment as they turn.
The flexible joint is an articulating spline-joint assembly that has a
male splined coupling and a female splined coupling. The couplings are
connected together with a swaged retainer to make a movable joint. The
flexible joints let the torque shafts have small angular changes of
alignment as they turn.
The plunging joint has a universal joint which moves on splines inside a
short drive shaft. The plunging joint gives a flexible joint:
- on the output side of the flap 1 actuator
- on the input side of the line gearbox.
Torque Shafts and Steady Bearings
Figure 018
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 27-54-00Page 35 1 1 May 01/05 1 1 1CES 1
Torque Shafts and Steady Bearings
Figure 018A
R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 27-54-00Page 36 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R Torque Shafts and Steady Bearings - Details Figure 019
R 1EFF : 1 1 1CES ALL 1 111 27-54-00 Page 37 May 01/04
Each torque shaft assembly has at least one movable end connection. The movable end connection has an indicator groove. This goes out of view when the splines at the connection are correctly engaged.
Steady bearings, which hold the torque shafts, are attached to the structure with bolts. Two types of steady bearing are installed:
-
a self-aligning ball bearing only
-
a self-aligning ball bearing and univeral joint assembly.
F. Actuator Track 1 6205CM(6255CM)
**ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 020) R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
(Ref. Fig. 020A)
**ON A/C 301-399,
(Ref. Fig. 020B)
**ON A/C ALL
The actuator is an assembly that has:
-an offset gearbox
-a rotary actuator.
(1) Offset Gearbox - Track 1
**ON A/C 001-049, 051-061, 101-105, 201-203,
(Ref. Fig. 021) R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
(Ref. Fig. 021A)
Actuator - Track 1 Figure 020
R 1EFF : 1 1 1CES 001-049, 051-061, 101-105, 201-203, 1 111 27-54-00 Page 39 May 01/05
Actuator - Track 1
Figure 020A
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-54-00Page 40 1401-499, 1Aug 01/05 1 1 1CES 1
R Actuator - Track 1
R Figure 020B
R 1EFF : 301-399, 1 27-54-00 Page 41
1 1 May 01/04
1 1
1CES 1
Offset Gearbox Figure 021
R 1EFF : 1 1 1CES 001-049, 051-061, 101-105, 201-203, 1 111 27-54-00 Page 42 May 01/05
Offset Gearbox
Figure 021A
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-54-00Page 43 1401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C 301-399,
(Ref. Fig. 021B)
**ON A/C 001-049, 051-061, 101-105, 201-203,
The offset gearbox casing contains:
-a through shaft
-the torque limiter
-reduction gearing
-the rotary actuator.
The power goes from the through shaft through the torque limiter to spur gears. The spur gears move the input shaft of the rotary actuator.
R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
The offset gearbox has:
-an actuator housing
-
a gear cover
-
a bevel housing
-
a torque limiter.
The actuator housing is a machined casting which contains the rotary actuator and the torque limiter. The gear cover is bolted to the actuator housing and seals the input side of the actuator.
The bevel housing is bolted to the gear cover and contains an input bevel gear. This engages with a bevel gear shaft that passes through the torque limiter to transmit the output drive to the flap drive system. An input gear is installed on the bevel gear shaft. The input gear engages with an idler gear installed between the input gear and a gear wheel assembly. This gear wheel assembly engages with, and transmits the drive to, the input gear of the rotary actuator.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(138)
