R 1EFF : 001-049, 053-061, 101-105, 201-203, 1 27-51-00Page 592 1 1 May 01/05 1 1 1CES 1
(2) Remove the PIN RIGGING-FLAPS (TRACK 1) (1) from the track 1 position and the PIN RIGGING FLAPS (2) from the track 2, 3 and 4 positions.
R **ON A/C 051-052, 062-099, 106-149, 151-199, 204-299, 401-499,
Subtask 27-51-00-080-050-B
D. Removal of the Rigging Tools
(1) Remove the KIT-FLAP RIGGING (98D27504038001):
(Ref. Fig. 506A/TASK 27-51-00-991-056-A)
-
for the inboard flap, from the flap track 2 beam assembly
-
for the outboard flap, from the flap track 3 beam assembly and from the track 4 beam assembly.
(a)
Remove the pin (12) and remove the fin (11) from the base assembly (15).
(b)
Hold the base assembly (15) and loosen the knurled screws (17).
(c)
Move the two lower clamps (16) clear of the flap track beam (18) and remove the base assembly (15).
(Ref. Fig. 505/TASK 27-51-00-991-055)
(2) Remove the PIN RIGGING-FLAPS (TRACK 1) (1) from the track 1 position and the PIN RIGGING FLAPS (2) from the track 2, 3 and 4 positions.
**ON A/C 301-399,
Subtask 27-51-00-080-050-C
D. Removal of the Rigging Tools
(1) Remove the KIT-FLAP RIGGING (98D27504113001):
(Ref. Fig. 506B/TASK 27-51-00-991-056-B)
-
for the inboard flap, from the flap track 2 beam assembly
-
for the outboard flap, from the flap track 3 beam assmbly and from the track 4 beam assembly.
(a)
Remove the pin (12) and remove the fin (11) from the base assembly (15).
(b)
Hold the base assembly (15) and loosen the knurled screws (17).
R 1EFF : 002-049, 051-099, 101-149, 151-199, 1 27-51-00Page 593 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(c) Move the two lower clamps (16) clear of the flap track beam (18) and remove the base assembly (15).
(Ref. Fig. 505A/TASK 27-51-00-991-055-A)
(2) Remove the PIN RIGGING FLAPS (1) from each actuator lever position. **ON A/C ALL
5. Close-up
________ Subtask 27-51-00-410-057
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Lift the flap track No. 2 movable fairing (Ref. TASK 57-55-11-410-001).
(3)
Lift the flap track No. 3 movable fairing (Ref. TASK 57-55-11-410-002).
(4)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) from the flap/slat control lever.
(5)
Remove the GROUND LOCK SLEEVE from the applicable MLG door actuator.
(6) Close the applicable MLG door (Ref. TASK 32-12-00-410-001). Subtask 27-51-00-942-062
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-51-00Page 594 1 1 May 01/05R 1 1 1CES 1
TASK 27-51-00-820-004
Adjustment of the Forward Eccentrics to the Datum Position
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(60)
