曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  (Ref. Fig. 501/TASK 27-54-00-991-038, 502/TASK 27-54-00-991-039, 503/TASK
 27-54-00-991-040) 
R  (1) Install the PIN RIGGING-FLAPS (TRACK 1) (1) at the track 1. 
R  (2) If you cannot install the PIN RIGGING-FLAPS (TRACK 1) (1) easily, do 
R  the steps that follow: 
R  (a) Removal of the Torque Shaft 6204CM (6254CM) 
R  1_  Install the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
R  PIVOT (98D27504030001) on a flap torque shaft, outboard of the 
R  component that you will remove (Ref. TASK 27-50-00-400-003). 
R  2_  Remove the nuts (5) and the bolts (6) from the torque shaft
R  (4). If applicable, remove the spacers. 
R  NOTE : Spacers between the universal joint (3) and the torque____ 
R  shaft (4) adjust the length of the transmission. It is 
R  possible that there are none or more than one spacer(s) 
R  installed. 
R  3_  Remove the universal joint (3).
R  (b) Adjustment of the flap drive system (for free rigging pin). 
R  1_  Loosen the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-
R  PIVOT as necessary to turn the torque shafts. 
R  2_  Turn the torque shaft 6206CM (6256CM) four turns in the
R  extension direction. 
R  3_  Turn the torque shaft 6206CM (6256CM) in the retraction
R  direction until the rigging pin (1) can be installed easily. 
R  4_  If the torque shaft 6206CM (6256CM) is accidentally turned too
R  far in the retraction direction: 
R  - Do the adjustment procedure again until the rigging pin (1) 
R  can be installed easily. 
R  (c) Preparation for Installation 
R  CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT._______ 
R  GREASE AND ASSEMBLY PASTE DO NOT MIX.

 

R Flap Transmission - Access Panels R Figure 501/TASK 27-54-00-991-038
 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-54-00Page 518 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1R Installation of the Flap Rigging Pins R Figure 502/TASK 27-54-00-991-039

 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-54-00Page 519 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1

R Torque Shafts - Flap Power Transmission
R Figure 503/TASK 27-54-00-991-040- 13 (SHEET 1)

 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-54-00Page 520 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1

R Torque Shafts - Flap Power Transmission
R Figure 503/TASK 27-54-00-991-040- 23 (SHEET 2)

 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-54-00Page 521 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1

R Torque Shafts - Flap Power Transmission
R Figure 503/TASK 27-54-00-991-040- 33 (SHEET 3)

 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-54-00Page 522 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1

R  WARNING : USE A PROTECTIVE EYE SHIELD/GOGGLES WHEN YOU USE_______ 
R  COMPRESSED AIR. DEBRIS AND/OR HIGH PRESSURE AIR CAN 
R  DAMAGE YOUR EYES. 
R  WARNING : DO NOT PUT COMPRESSED GAS IN CONTACT WITH YOUR SKIN._______ 
R  THE GAS CAN GO THROUGH THE SKIN AND MAKE BUBBLES IN THE 
R  BLOOD. THIS CONDITION CAN KILL YOU. 
R  WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER_______ 
R  SPECIAL MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. 
R  OBEY THE MANUFACTURERS INSTRUCTIONS. 
R  PUT ON PROTECTIVE CLOTHING. 
R  DO NOT GET THEM IN YOUR MOUTH. 
R  DO NOT SMOKE. 
R  DO NOT BREATHE THE GAS. 
R  THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN 
R  IRRITANT. 
R  GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 
R  1_  Use a clean lint-free cotton cloth MISCELLANEOUS (Material No.
R  19-003) and the cleaning agent CLEANING AGENTS (Material No. 
R  11-026) to clean the parts that follow: 
R  - The nuts (5) 
R  - The bolts (6) 
R  - The flange of the universal joint (3) 
R  - The flange of the torque shaft (4). 
R  2_  Dry the parts with compressed air.
R  3_  Make sure that the parts retained from the removed component
R  are clean and in the correct condition. 
R  4_  Clean the component interface and/or the adjacent area.
R  5_  Lubricate the torque splines as follows:
R  CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT._______ 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(152)