CAUTION : MAKE SURE THAT THE DISCONNECTED PARTS DO NOT TOUCH
_______ AND/OR CATCH THE ADJACENT STRUCTURE WHEN YOU MOVE THE FLAP. THIS WILL PREVENT DAMAGE TO THE WING.
1 Manually push the tab forward and install the DISTANCE GAUGES
_
(98D27504114000) (60) and (64).
a At the hinge 1A position, put the distance gage (60) in
_
position:
-
install the rear pin (61)
-
install the forward pin (58) and lock it with the knurled screw (59).
b At the track 2 position, put the distance gage (64) in
_
position:
-
install the forward pin (62) and lock it with the knurled screw (63)
-
install the rear pin (65) and lock it with the knurled screw (66).
(7) For the outboard flap:
(a) Disconnect the tab drive control-rod (82) from the track 3 carriage (77). (Ref. Fig. 611/TASK 27-54-00-991-016)
1 Remove and discard the cotter pin (80).
_
2 Remove the nut (81), the washer (79), the bolt (83) and the
_
loose bush (78).
(b) Disconnect the tab drive control-rod (97) from the track 4 carriage (94). (Ref. Fig. 612/TASK 27-54-00-991-021)
1 Remove and discard the cotter pin (101).
_
2 Remove the nut (100), the washer (99) and the loose bush (98).
_
R 1EFF : 301-399, 1 27-54-00Page 641 1 1 May 01/05 1 1 1CES 1
Distance Gauges - Location and Detail
R Figure 610/TASK 27-54-00-991-020
R 1EFF : 301-399, 1 27-54-00 Page 642
1 1 May 01/05
1 1
1CES 1
Details of the Tab Drive Control-Rod (Track 3) R Figure 611/TASK 27-54-00-991-016
R 1EFF : 301-399, 1 27-54-00Page 643 1 1 May 01/05 1 1 1CES 1
Details of the Tab Drive Control-Rod (Track 4) R Figure 612/TASK 27-54-00-991-021
1EFF : 301-399, 1 27-54-00Page 644 1 1 May 01/05 1 1 1CES 1 3 Remove the hinge pin (96) sufficiently to let you remove the
_ tab drive control-rod (97). Do not fully remove the hinge pin (96).
NOTE : If you fully remove the hinge pin (96) from the
____ carriage (94), the roller bearing block (95) will fall out of alignment.
4 Fully install the hinge pin (96) and temporarily install the
_
nut (100).
(c) Install the distance gages:
(Ref. Fig. 613/TASK 27-54-00-991-022)
CAUTION : MAKE SURE THAT THE DISCONNECTED PARTS DO NOT TOUCH
_______ AND/OR CATCH THE ADJACENT STRUCTURE WHEN YOU MOVE THE FLAP. THIS WILL PREVENT DAMAGE TO THE WING.
1 Manually push the tab forward and install the DISTANCE GAUGES
_ (98D27504115000) (112) and (115) at the track 3 and the track 4 positions.
2 At the track 3 position, put the distance gage (112) in
_ position and install the pins (113) and (114).
3 At the track 4 position, put the distance gage (115) in
_ position and install the pin (116).
(8) Fully retract the flaps (Ref. TASK 27-50-00-866-009).
**ON A/C ALL
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 614/TASK 27-54-00-991-027)
**ON A/C 301-399,
(Ref. Fig. 614A/TASK 27-54-00-991-027-A)
Distance Gauges - Location and Detail
R Figure 613/TASK 27-54-00-991-022
R 1EFF : 301-399, 1 27-54-00 Page 646
1 1 May 01/05
1 1
1CES 1
INTENTIONALLY BLANK
R 1 1
27-54-00Page 647
1 1 May 01/05 1 1 1CES 1
Flap to Rotary Actuator Drive Lever - To Disconnect the Inboard Flap Figure 614/TASK 27-54-00-991-027- 12 (SHEET 1)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-00Page 648 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Flap to Rotary Actuator Drive Lever - To Disconnect the Inboard Flap Figure 614/TASK 27-54-00-991-027- 22 (SHEET 2)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-00Page 649 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Flap to Rotary Actuator Drive Lever - To Disconnect the Inboard Flap R Figure 614A/TASK 27-54-00-991-027-A
R 1EFF : 301-399, 1 27-54-00Page 650 1 1 May 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 615/TASK 27-54-00-991-029) **ON A/C 301-399,
(Ref. Fig. 615A/TASK 27-54-00-991-029-A) **ON A/C ALL
R (Ref. Fig. 616/TASK 27-54-00-991-010) **ON A/C 001-049, 101-102, 151-199, 401-499,
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(168)
