R 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-51-00Page 567 1204-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R Installation of the Flap Rigging Kit
R Figure 506B/TASK 27-51-00-991-056-B
R 1EFF : 301-399, 1 27-51-00 Page 568
1 1 May 01/04
1 1
1CES 1
**ON A/C 001-001,
Subtask 27-51-00-220-056-B
B. To Do a Check of the Inboard Flap Rigged Position
(Ref. Fig. 507/TASK 27-51-00-991-019)
NOTE : The tolerances given in the work steps that follow are in-service
____ tolerances only. They are not initial adjustment tolerances. The tolerances for initial adjustment are given in the flap rigged position adjustment procedure (Ref. TASK 27-51-00-820-008).
(1)
At the track 2 position, measure:
(a)
The dimension F (between the end of the trailing edge and the fin (29)). This must be 20 mm (0.8 in.) +/- 5 mm (0.2 in.) measured from the inboard side of the fin (29).
(b)
The dimension G (between the bottom of the trailing edge and the fin (29)). This must be 10 mm (0.4 in.) +/- 1.5 mm (0.06in.).
(2)
At the inboard end of the flap, measure:
(a) The dimension E (between the shroud-box trailing-edge lower surface and the flap upper surface at the WX500 position). This must be between 3.5 mm (0.14 in.) and 9 mm (0.35 in.).
(3)
If the flap rigged position is not correct, adjust as necessary until the flap is in the specified limits (Ref. TASK 27-51-00-820-008).
R **ON A/C 002-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-51-00-220-056
B. To Do a Check of the Inboard Flap Rigged Position
(Ref. Fig. 508/TASK 27-51-00-991-057)
NOTE : The tolerances given in the work steps that follow are in-service
____ tolerances only. They are not initial adjustment tolerances. The tolerances for initial adjustment are given in the flap rigged position adjustment procedure (Ref. TASK 27-51-00-820-008).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page 569 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Inboard Flap Rigging Dimensions
Figure 507/TASK 27-51-00-991-019
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page 570 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R Inboard Flap Rigging Dimensions
R Figure 507A/TASK 27-51-00-991-019-A
R 1EFF : 301-399, 1 27-51-00 Page 571
1 1 May 01/04
1 1
1CES 1
Inboard Flap Rigging Dimensions
Figure 508/TASK 27-51-00-991-057
R 1EFF : 002-049, 051-099, 101-149, 151-199, 1 27-51-00Page 572 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
(1) At the track 2 position: NOTE : The scale must be read from the outboard side of the flap
____
track beam.
(a) Make sure that the top surface of the trailing edge aligns (+/- 4 mm (0.16 in.)) with the zero line on the scale block (30).
(2)
At the inboard end of the flap, measure:
(a) The dimension E (between the shroud-box trailing edge lower surface and the flap upper surface at the WX500 position). This must be between 1.5 mm (0.06 in.) and 11 mm (0.43 in.).
(3)
If the flap rigged position is not correct, adjust as necessary until the flap is in the specified limits.
**ON A/C 301-399,
Subtask 27-51-00-220-056-C
B. To Do a Check of the Inboard Flap Rigged Position
(Ref. Fig. 508A/TASK 27-51-00-991-057-A)
NOTE : The tolerances given in the work steps that follow are in-service
____ tolerances only. They are not initial adjustment tolerances. The tolerances for initial adjustment are given in the flap rigged position adjustment procedure (Ref. TASK 27-51-00-820-009).
(1) At the track 2 position: NOTE : The scale must be read from the outboard side of the flap
____
track beam.
(a) Make sure that the top surface of the trailing edge aligns (+/- 4 mm (0.16 in.)) with the zero line on the scale block (30).
(2)
At the inboard end of the flap, measure:
(a) The dimension E (between the shroud-box trailing edge lower surface and the flap upper surface at the WX500 position). This must be between 1.5 mm (0.06 in.) and 11 mm (0.43 in.).
(3)
If the flap rigged position is not correct, adjust as necessary until the flap is in the specified limits.
R 1EFF : 002-049, 051-099, 101-149, 151-199, 1 27-51-00Page 573 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM FLIGHT CONTROLS 飛行操縱4(56)
