(2)
 Make sure that the remaining fuel has been drained from the applicable fuel tank (Ref. TASK 28-25-00-650-003).

 (3)
 Make sure that the access platform is below the applicable access panel 540KB (640KB).

 (4)
 Make sure that the applicable access panel 540KB (640KB) is removed (Ref. TASK 28-10-00-910-002), (Ref. TASK 57-27-11-000-002).

 (5)
 Make sure that the applicable refuel diffuser is removed (Ref. TASK 28-25-42-000-001).

 4. Procedure
_________
 (Ref. Fig. 401/TASK 28-25-57-991-001) Subtask 28-25-57-420-051
 A. Preparation for Installation
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL

_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1)
 Clean the component interfaces and the adjacent areas with a lint-free cloth made moist with CLEANING AGENTS (Material No. 11-004).

 (2)
 Do an inspection of the component interface and/or the adjacent area.

 (3)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-25-57Page 407 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 28-25-57-420-050

 B. Installation of the Air-Inlet Valve 161QM (162QM)
 (1)
 Remove the blanking plugs from the disconnected pipe (1) end and the air-inlet valve (7).

 (2)
 Use the bolts (5) to install the air-inlet valve (7) on the bracket (6). Tighten the bolts (5).

 (3)
 Lubricate the union (8) with FUELS (Material No. 01-001)

 (4)
 Use the union (8) to connect the pipe (1) to the air-inlet valve (7). Tighten the union (8).

 (5)
 Use the bolt (3) and the nut (4) to connect the bonding lead (2) to the air-inlet valve (7). Tighten the nut (4).

 (6)
 Do a bonding check of the bonding lead (2) (Ref. TASK 20-28-00-912-006).

 (7)
 Install the refuel diffuser (Ref. TASK 28-25-42-400-001).

 5. Close-up
________ Subtask 28-25-57-410-050
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the applicable access panels 540KB (640KB) (Ref. TASK 57-27-11-400-002).

 Subtask 28-25-57-650-052
 B. Fuel Configuration
 (1) Refuel, defuel or transfer fuel as necessary (Ref. TASK 12-11-28-650-003), (Ref. TASK 28-25-00-650-001) or (Ref. TASK 28-25-00-869-001).
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-25-57Page 408 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 28-25-57-942-050

 C. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the safety barriers.

 (3)
 Remove the warning notice(s).

 (4)
 Remove the access platform(s).

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-25-57Page 409 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 MAIN TRANSFER SYSTEM - DESCRIPTION AND OPERATION

________________________________________________
 1. General_______
 The main transfer system controls the flow of fuel from the center (transfer) tank to the two wing tanks. The system uses jet pumps to move the fuel from the center (transfer) tank to the wing tanks. The Fuel Level Sensing Control Unit (FLSCU) (Ref. 28-46-00) automatically controls the system, but the crew can, if necessary, manually control it from the cockpit.
 The Engine/Warning Display (EWD) (Ref. 31-66-00) and the System Display (SD) (which together make the ECAM) give main transfer system information to the crew. If specified failures occur:
 -a warning is given on the EWD

 -the FUEL page shows on the SD.
 When necessary the crew can make a selection on the ECAM control panel (Ref.
 31-56-00) to look at the FUEL page.

 1EFF : 301-399, 1 28-26-00Page 1 1 1 May 01/04 1 1 1CES 1

 2. Component Location__________________
 (Ref. Fig. 001, 002)
 -------------------------------------------------------------------------------FIN | FUNCTIONAL DESIGNATION | PANEL|ZONE|ACCESS | ATA | | | | DOOR | REF.
 -------------------------------------------------------------------------------157QM JET PUMP-L, CENTER TANK 141 147AZ 28-26-41 158QM JET PUMP-R, CENTER TANK 142 148AZ 28-26-41 220QM STRAINER-JET PUMP L, CENTER TANK 141 147AZ 28-26-42 221QM STRAINER-JET PUMP R, CENTER TANK 142 148AZ 28-26-42 11QL ACTUATOR-JET PUMP 1 CTL VALVE, CTR 195 195BB 28-26-51 TK 12QL ACTUATOR-JET PUMP 2 CTL VALVE, CTR 196 196BB 28-26-51 TK 153QM FUEL CONTROL VALVE-JET PUMP, L WING 141 147AZ 28-10-00 TK 154QM FUEL CONTROL VALVE-JET PUMP, R WING 142 148AZ 28-10-00 TK 155QM CLAMP-V BAND 195 195BB 28-10-00 156QM CLAMP-V BAND 196 196BB 28-10-00
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油4(111)