(2)
Make sure that the access panel 622HB is removed.
1EFF : ALL 1 28-25-41Page 434 1 1 Aug 01/05 1 1 1CES 1 **ON A/C 051-051,
Subtask 28-25-41-860-054-A
B. Aircraft Maintenance Configuration
(1) Make sure that the access platform is below the applicable refuel/defuel coupling 100QM(40QM).
(2) Make sure that the applicable access panel 522HB(622HB) is removed. **ON A/C ALL
Subtask 28-25-41-865-054
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure
_________ R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 405/TASK 28-25-41-991-007)
**ON A/C 051-051,
(Ref. Fig. 405A/TASK 28-25-41-991-007-A)
1EFF : ALL 1 28-25-41Page 435 1 1 Aug 01/05 1 1 1CES 1R **ON A/C ALL
Subtask 28-25-41-420-058
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area with a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
Subtask 28-25-41-420-059
B. Installation of the Refuel/Defuel Coupling Element Assembly
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Lubricate the new O-ring (2) with FUELS (Material No. 01-001) or COMMON GREASE (Material No. 04-012).
(2)
Install the O-ring (2) and the laminated shim(s) (3).
(3)
Install the element assembly (4) and the shroud-ring (5) in their correct positions.
(4)
Install the washers (6), the attachment tag (10) and the bolts (7). TORQUE the bolts (7) to between 0.3 and 0.34 m.daN (26.54 and 30.08 lbf.in).
(5)
Install the chain (9) on the attachment tag (10).
NOTE : The chain (9) is spring-loaded into a protective sleeve on the
____
coupling cap (8).
1EFF : ALL 1 28-25-41Page 436 1 1 May 01/05 1 1 1CES 1
(6) Install the coupling cap (8) on the coupling (1). CAUTION : MAKE SURE THAT THE HANDLE OF THE REFUEL COUPLING CAP POINTS
_______ AFT WHEN THE CAP IS CLOSED AND LOCKED.
R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 28-25-41-410-062
C. Close Access
(1) Install the access panel 622HB.
Subtask 28-25-41-820-054
D. Adjustment of the Coupling WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1)
Make sure that these dimensions are correct:
(Ref. Fig. 402/TASK 28-25-41-991-003)
-
dimension 'a' must be equal at all positions around the coupling cap (8), +/- 0.5 mm (0.0196 in.)
-
dimension 'x' must not be more than 1.0 mm (0.0393 in.)
-
dimension 'y' must not be more than 1.0 mm (0.0393 in.)
-
dimension 'z' must not be more than 0.13 mm (0.0051 in.).
(2)
If dimension 'a' is incorrect:
(a)
Temporarily remove the access panel 622HB. (Ref. Fig. 404/TASK 28-25-41-991-006)
(b)
Remove the coupling cap (8) from the coupling (1).
1EFF : ALL 1 28-25-41Page 437 1 1 Aug 01/05 1 1 1CES 1
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油4(67)
