曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  correct positions. 
R  (k) Install the washers (6), the attachment tag (10) and the bolts 
R  (7). TORQUE the bolts (7) to between 0.3 and 0.34 m.daN (26.54 
R  and 30.08 lbf.in). 
R  (l) Install the chain (9) on the attachment tag (10). 
R  NOTE : The chain (9) is spring-loaded into a protection sleeve on____ 
R  the coupling cap (8). 
R  (m) Install the coupling cap (8) on the coupling (1). 
R  CAUTION : MAKE SURE THAT THE HANDLE OF THE REFUEL COUPLING CAP_______ 
R  POINTS AFT WHEN THE CAP IS CLOSED AND LOCKED.

 

 E. Preparation for Test
 (1)
 Install the applicable access panel 522HB(622HB).

 (2)
 Measure the dimensions 'x', 'y' and 'z' again to make sure that they are correct.

 (3)
 Refuel the aircraft through the coupling (1) (Ref. TASK 12-11-28-650-003).

 (4) Remove the applicable access panel 522HB(622HB).
 **ON A/C ALL

 Subtask 28-25-41-790-053
 F. Test
 (1) If you adjusted the laminated shim(s) (3), examine the joint of the element assembly (4) for leaks.
 5. Close-up
________ R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 28-25-41-410-061
 A. Close Access
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Install the access panel 622HB.

 1EFF : ALL 1 28-25-41Page 441 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 28-25-41Page 442 1 1 May 01/05 1 1 1CES 1R COUPLING/CAP - REFUEL/DEFUEL (40QM,41QM,100QM,101QM) - INSPECTION/CHECK

R  **ON A/C 051-051, 
R  Subtask 28-25-41-410-061-A 
R  A. Close Access 
R R  (1) Make sure that the work area is clean and clear of tool(s) and other items. 
R  (2) Install the applicable access panel 522HB(622HB). 
R  **ON A/C ALL
 Subtask 28-25-41-865-053
 B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
 Subtask 28-25-41-942-056
 C. Removal of Equipment
 (1) Remove the safety barriers.
 (2) Remove the access platform(s).
 (3) Remove the warning notice(s).
 (4) Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 

_______________________________________________________________________ TASK 28-25-41-200-001 R Detailed Inspection of Coupling Refuel/Defuel WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1.
 Reason for the Job

__________________
 Refer to the MPD TASK: 282541-01

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific access platform 3.6 m (11 ft. 10 in.)

 1EFF : ALL 1 28-25-41Page 601 1 1 May 01/05 1 1 1CES 1

 B. Referenced Information -------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------28-00-00-910-001 Fuel Safety Procedures

R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 28-25-41-991-005 Fig. 601
 **ON A/C 051-051,
 28-25-41-991-005-A Fig. 601A
 **ON A/C ALL
 3. Job Set-up
__________ R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 (Ref. Fig. 601/TASK 28-25-41-991-005)
 **ON A/C 051-051,

 (Ref. Fig. 601A/TASK 28-25-41-991-005-A)
 **ON A/C ALL

 Subtask 28-25-41-941-057
 A. Safety Precautions
 WARNING : OBEY THE FUEL SAFETY PROCEDURES.

_______
 (1)
 You must obey the fuel safety procedures (Ref. TASK 28-00-00-910-001) when you do work on the fuel system.

 (2)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油4(69)