-monitor the fuel quantity indications for each fuel tank
-write down the fuel quantity indications when they have become stable.
1EFF : 301-399, 1 28-26-00Page 502 1 1 May 01/04 1 1 1CES 1
Cockpit Fuel Control Switches and Indications
Figure 501/TASK 28-26-00-991-001
1EFF : 301-399, 1 28-26-00Page 503 1 1 May 01/04 1 1 1CES 1 Subtask 28-26-00-865-050
D. Make sure that this(these) circuit breaker(s) is(are) closed: -------------------------------------------------------------------------------
PANEL ------ DESIGNATION --------------------------------------------------- IDENT. LOCATION----------------------
121VU FUEL/L WING TK/PUMP2 SPLY 7QA N26
121VU FUEL/L WING TK/PUMP1 SPLY 1QA N23
121VU FUEL/R WING TK/PUMP2 SPLY 8QA Q26
121VU FUEL/R WING TK/PUMP1 SPLY 2QA Q23
121VU FUEL/CTR TK/AUTO/CTL 3QL R27
121VU FUEL/CTR TK/L&R XFR/CTL & IND 2QL R26
121VU FUEL/CTR TK/L&R XFR/CTL & IND 1QL R25
123VU L WING TK/PUMP 1/STBY SPLY 11QA AD12
123VU R WING TK/PUMP 1/STBY SPLY 12QA AE12
4. Procedure_________
(Ref. Fig. 501/TASK 28-26-00-991-001)
Subtask 28-26-00-710-050
A. Operational Test of the Main Transfer System
(1) Do this test:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the panel 40VU:
-
make sure that all of the fuel pump P/BSWs are released (out)
-
make sure that the MODE SEL P/BSW is released (out).
2. On the panel 25VU:
-
put the ANN LT switch to the TEST position
-
put the ANN LT switch to the BRT or the DIM position.
3. On the panel 40VU:On the panel 40VU:
-
make sure that all of the fuel pumpP/BSW OFF lights are on
-
make sure that the MODE SEL P/BSW MANlight is on.
-
make sure that all of the P/BSWlights come on
-
make sure that all of the P/BSWlights go back to their set configuration
1EFF : 301-399, 1 28-26-00Page 504 1 1 May 01/04 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
-
push (in) the L TK PUMPS 1 and 2 P/BSWs
-
push (in) the CTR TK L XFR P/BSW.
4.
Let the pumps operate for five minutes.
5.
On the panel 40VU:
-after five minutes, release (out) the CTR TK L XFR and the L TK PUMPS 1 and 2 P/BSWs.
6.
On the ECAM SDU:
-monitor the fuel quantity indications
-the L TK PUMPS 1 and 2 P/BSW FAULTlights come on momentarily and then go off
-when the P/BSW FAULT lights go off, the L TK PUMPS 1 and 2 OFF lights go off.
On the ECAM SDU:
-
the indications for the LEFT pumps change from amber cross-line (pump not in operation) to green in-line (pump in operation).
On the panel 40VU:
-
the OFF light of the CTR TK L XFR P/BSW goes off.
On the ECAM SDU:
-
the indication for the CTR LH pump changes from amber cross-line (pump not in operation) to green in-line (pump in operation)
-
the fuel quantity indication for thecenter tank decreases, while the fuel quantity indication for the LH wing tank increases.
On the panel 40VU:
-
the OFF lights of the CTR TK L XFRand the L TK PUMPS 1 and 2 P/BSWscome on
On the ECAM SDU:
-
the fuel pump indications show amber cross-line (pumps not in operation)
-make sure that the fuel quantity indication for the LH wing tank stops increasing.
1EFF : 301-399, 1 28-26-00Page 505 1 1 May 01/04 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
-write down the fuel quantity indications when they have become stable.
7.
Use the fuel quanity indications (that you wrote down) to calculate the fuel transfer rate from the center tank to the LH wing tank.
8.
On the panel 40VU:
-
push (in) the R TK PUMPS 1 and 2 P/BSWs
-
push (in) the CTR TK R XFR P/BSW.
9.
Let the pumps operate for five minutes.
10.
On the panel 40VU:
The transfer rate must be between 70kg/min and 106 kg/min (154 lb/min and234 lb/min).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油4(115)
