R **ON A/C 001-049, 052-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 28-25-00-410-067
B. Close Access
(1)
Install the coupling cap 41QM. CAUTION : MAKE SURE THAT THE HANDLE OF THE REFUEL COUPLING CAP POINTS
_______ AFT WHEN THE CAP IS CLOSED AND LOCKED.
(2)
Close the access panel 192MB.
(3)
For the left refuel valve 7QU, close the access panel 522JB.
(4)
For the right refuel valve 8QU, close the access panel 622JB.
(5)
For the center tank refuel valve 10QU, close the RH MLG door 744 (Ref. TASK 32-12-00-410-001).
**ON A/C 051-051,
Subtask 28-25-00-410-067-A
B. Close Access
(1)
Install the coupling cap 101QM(41QM). CAUTION : MAKE SURE THAT THE HANDLE OF THE REFUEL COUPLING CAP POINTS
_______ AFT WHEN THE CAP IS CLOSED AND LOCKED.
(2)
Close the access panel 192MB.
1EFF : ALL 1 28-25-00Page 434 1 1 Aug 01/05 1 1 1CES 1
(3)
For the left refuel valve 7QU, close the access panel 522JB.
(4)
For the right refuel valve 8QU, close the access panel 622JB.
(5)
For the center tank refuel valve 10QU, close the RH MLG door 744 (Ref. TASK 32-12-00-410-001).
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 28-25-00-860-062
C. Aircraft Maintenance Configuration
(1)
Disconnect these bonding/ground cables:
-between the aircraft and the fuel tanker/pump unit
-
if applicable, between the fuel tanker/pump unit and the ground
-
if applicable, between the aircraft and the ground.
(2)
Write in the A/C technical log to do a check of the fuel configuration.
NOTE : Fuel correction is automatic after the fuel pumps are set to
____ on (the wing tank outer cells must be filled).
**ON A/C 301-399,
Subtask 28-25-00-860-062-A
C. Aircraft Maintenance Configuration
(1)
Disconnect these bonding/ground cables:
-between the aircraft and the fuel tanker/pump unit
-
if applicable, between the fuel tanker/pump unit and the ground
-
if applicable, between the aircraft and the ground.
(2)
Write in the A/C technical log to do a check of the fuel configuration.
1EFF : ALL 1 28-25-00Page 435 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
Subtask 28-25-00-942-076
D. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 28-25-00Page 436 1 1 May 01/05R 1 1 1CES 1
TASK 28-25-00-040-007
Fuel Quantity Panel System (Refueling)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MMEL TASK: 28-25-02
Fuel Quantity Indicator
Refueling Panel
(FAA Only)
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific access platform 3.5 m (11 ft. 6 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-11-28-650-007 Use of Magnetic Level Indicators (MLI) 12-34-24-869-001 Aircraft Grounding for the Refuel/Defuel Operations 24-41-00-861-002 Energize the Aircraft Electrical Circuits from the
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油4(47)
