R 1EFF : 301-399, 1 32-11-27Page 617 1 1 May 01/04 1 1 1CES 1
R (e) Install the top torque-link pin (Ref. TASK 32-11-27-400-001).
R NOTE : Refer to (Ref. CMM 321222) for corrective action.____
R (2) Do a check of the radial clearance at the bottom torque-link joint as
R follows:
R (a) Carefully remove the bottom torque-link pin (Ref. TASK 32-11-27-
R 000-001).
R (Ref. Fig. 602/TASK 32-11-27-991-010)
R (b) Use an external micrometer 50-75 mm (2.0-3.0 in.) to measure the
R diameter Y of the pin and record the minimum dimension.
R NOTE : Measure the diameter of the pin where it touches the____
R bushes in the bottom torque link and the shock absorber.
R (c) Use an internal micrometer to measure the internal diameter G and
R H of the bushes in the:
R - bottom torque link
R - shock absorber.
R Record the maximum dimension.
R (d) Subtract dimension Y from the maximum dimension G or H to give
R the clearance at the bottom pin position. A maximum in-service
R clearance of 0.119 mm (0.0046 in.) is permitted.
R (e) Install the bottom torque-link pin (Ref. TASK 32-11-27-400-001).
R NOTE : Refer to (Ref. CMM 321222) for corrective action.____
R Subtask 32-11-27-220-060-C
R C. Inspection Procedure
R (1) Do a check of the radial clearances at the torque-link apex joint as
R follows:
R (a) Carefully remove the torque-link apex pin (1) and the torque-link
R sleeves (2) and (3) (Ref. TASK 32-11-27-000-001). Make sure that
R each sleeve is correctly identified with the applicable torque
R link.
R (Ref. Fig. 603A/TASK 32-11-27-991-008-B)
R 1EFF : 301-399, 1 32-11-27Page 618 1 1 May 01/04 1 1 1CES 1
R (b) At the top torque-link bushes:
R 1_ Use an internal micrometer to measure the internal diameter R
R and S of the bushes. Record the maximum dimension.
R 2_ Use an external micrometer 25-50 mm (1.0-2.0 in.) to measure
R the external diameter P of the sleeve (2) and record the
R minimum dimension.
R 3_ Subtract dimension P from the maximum dimension R or S to give
R the sleeve clearance. A maximum in-service sleeve clearance of
R 0.50 mm (0.0196 in.) is permitted.
R 4_ Use an internal micrometer to measure the internal diameter Q
R of the sleeve (2) and record the maximum dimension.
R 5_ Use an external micrometer 25-50 mm (1.0-2.0 in.) to measure
R the external diameter N of the pin (1) and record the minimum
R dimension.
R NOTE : Measure the diameter of the pin where it touches the____
R top torque link.
R 6_ Subtract dimension N from the maximum dimension Q to give the
R pin clearance. A maximum in-service pin clearance of 0.134 mm
R (0.0052 in.) is permitted.
R (c) At the bottom torque-link bushes:
R 1_ Use an internal micrometer to measure the internal diameter T
R and U of the bushes. Record the maximum dimension.
R 2_ Use an external micrometer 25-50 mm (1.0-2.0 in.) to measure
R the external diameter W and X of the sleeve (3). Make sure
R that the measurements are taken at a position 20 mm (0.7874
R in.) from each end of the sleeve (3).
R NOTE : The dimensions are taken at the positions W and X to____
R make sure that only the parallel part of the sleeve is
R measured.
R 3_ Subtract dimension W from the maximum dimension T to give the
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM LANDING GEAR 起落架2(104)
