(6)
Remove the applicable TPIS rotating mechanisms (Ref. TASK 32-49-18-000-001).
(7) Remove the applicable tachometers (Ref. TASK 32-42-57-000-001). R **ON A/C 301-399, 401-499,
Subtask 32-11-43-010-056-A
D. Get Access
(1)
Put the access platform in position adjacent to the applicable MLG, below zone 730 or 740.
(2)
Open the applicable access panel 574AB, 674AB.
(3)
Open the applicable MLG door (Ref. TASK 32-12-00-010-001).
(4)
Remove the applicable wheels (Ref. TASK 32-41-11-000-006).
(5)
Remove the applicable brake fan assemblies (Ref. TASK 32-48-51-000-005).
(6)
Remove the applicable tachometers (Ref. TASK 32-42-57-000-001).
R 1EFF : 051-099, 301-399, 401-499, 1 32-11-43Page 447 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
4. Procedure
_________
**ON A/C 001-003, 051-052,
(Ref. Fig. 408/TASK 32-11-43-991-028) R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 408A/TASK 32-11-43-991-028-A)
**ON A/C ALL
(Ref. Fig. 409/TASK 32-11-43-991-029)
**ON A/C 001-003, 051-052,
Subtask 32-11-43-020-062
A. Removal of the 1M and 2M Harnesses from the MLG Axle CAUTION : MAKE SURE THAT ALL ELECTRICAL CONNECTORS ARE IDENTIFIED WITH
_______ THEIR FIN NO. TO CORRECTLY CONNECT EACH PLUG TO ITS RELATED RECEPTACLE. INCORRECT CONNECTION OF THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO THE AIRCRAFT ELECTRICAL SYSTEM.
(1) For the 1M harness:
(a)
Remove the nuts (4), the washers (3) and the bolts (1) to release the cable support (2) from the bracket (6).
(b)
Disconnect the MLG leg harness electrical connector 4051VC (4052VC) (5).
(c)
Remove the nuts (13), the washers (14) and the bolts (17).
(d)
Loosen the connector nut (16) to release the electrical connector
(15) from the bracket (6).
1EFF : ALL 1 32-11-43Page 448 1 1 Aug 01/05 1 1 1CES 1
(2)
For the 2M harness:
(a)
Remove the nuts (9), the washers (10) and the bolts (12) to release the cable support (11) from the bracket (7).
(b)
Disconnect the MLG leg harness electrical connector 4053VC (4054VC) (8).
(c)
Remove and discard the lockwire from the bolts (21).
(d)
Remove the bolts (21), the washers (20) and remove the clamp (22) from the cable (19).
(e)
Remove the nuts (26), the washers (25) and the bolts (18).
(f)
Loosen the connector nut (23) to release the electrical connector
(24) from the bracket (7).
(3)
Carefully remove the six cableforms of the 1M and 2M harnesses from the axle through the cable access holes. Do not make kinks in the harnesses.
(4) Put blanking caps on the disconnected electrical connectors. R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 32-11-43-020-062-A
A. Removal of the 1M and 2M Harnesses from the MLG Axle CAUTION : MAKE SURE THAT ALL ELECTRICAL CONNECTORS ARE IDENTIFIED WITH
_______ THEIR FIN NO. TO CORRECTLY CONNECT EACH PLUG TO ITS RELATED RECEPTACLE. INCORRECT CONNECTION OF THE ELECTRICAL CONNECTORS CAN CAUSE DAMAGE TO THE AIRCRAFT ELECTRICAL SYSTEM.
(1)
For the 1M harness:
(a) Disconnect the axle harness electrical connector 4051VC (4052VC)
(3) from the connector (2) installed on the bracket (1).
(2)
For the 2M harness:
(a)
Remove and discard the lockwire from the bolts (4).
(b)
Remove the bolts (4), the washers (5) and remove the cable clamp (6).
1EFF : ALL 1 32-11-43Page 449 1 1 Aug 01/05 1 1 1CES 1
MLG Axle Harnesses 1M and 2M - Location and Detail Figure 408/TASK 32-11-43-991-028- 12 (SHEET 1)
R 1EFF : 001-003, 051-052, 1 32-11-43Page 450 1 1 May 01/05 1 1 1CES 1
MLG Axle Harnesses 1M and 2M - Location and Detail Figure 408/TASK 32-11-43-991-028- 22 (SHEET 2)
R 1EFF : 001-003, 051-052, 1 32-11-43Page 451 1 1 May 01/05 1 1 1CES 1
MLG Axle Harnesses 1M and 2M - Location and Detail
Figure 408A/TASK 32-11-43-991-028-A
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-43Page 452 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
MLG Axle Harnesses 1M and 2M - Cableform Identification
Figure 409/TASK 32-11-43-991-029
R 1EFF : ALL 1 32-11-43Page 453 1 1 May 01/05 1 1 1CES 1 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架2(121)
